Search results

Hi guys So first question is what is wait time to get one? Next I have a built motor with edelbrock stage 2, fore dual fuel setup 1050x injectors and on e85 Would I need to upgrade to 1300 injectors I’m looking at doing the 132 throttle body and upgraded heat exchanger on the 6 rib setup. Any...

Hi everyone, I think my intercooler pumpmight be going on my 19 gt stage 2. Wondering what would be a good replacement maybe even better than the one edelbrock sends out? EB seems to be out of stock of many late model pumps as well. Thanks any info It’s much appreciated

So recent got my car back from upgrading fuel system noticed now after pump for intercooler turns off the fluid is low but if I let it cool and open the filler the fluid fills back up into the over flow where it should. Am I just not letting the car cool off or do I have an air pocket or...

I read an article that edelbrock is closing its headquarters. Anyone know what this might mean for everyone that has an edelbrock s/c?

I’m not a dyno expert at all. I had my car dynod one place it read 697 with eb stage 2 and headers 1050x injectors. Anything dynojet read 600 what would cause such a difference in dyno number? Only difference is on last pull I had cf drive shaft built a10 upgrade steels and street radials...

I’m thinking about switching to E85 on my edelbrock I’ll be doing a fore fuel system. My question is I read that pump e85 isn’t always true 85% so how does the computer handle say E70 % from the pump since the flex fuel cal is not turned on and it’s just automatically advancing for e85? thanks...

Can anyone recommend a shop that has the knowledge to do a 10r80 McLeod clutch pack swap. Dealer won’t do it because car is under warrenty they say. Thanks for recommendations in advance !!!

Hi, Currently have eb stage 2 setup looking to add a ic tank to the front probably 2-3 gals Any suggestions would be great thanks!

Hi everyone looking at getting a killer chiller installed and was looking to add a 1 gal holding tank to the front. I’m running an edelbrock stage 2 kit. Any recommandions would be much appreciated

Looking to see if any vendors of stock of the Anderson composite GT350R fenders in CF Ready to purchase if you do

Hi, Wondering if there is a way to do a security paratmeter reset at home? My alarm goes off after I lock the door and then try to open the door. It does it with both keys. Was told I need a security parameter reset but dealership won’t do it thanks for any help

I have a 2019 gt convert and it will randomly set alarm off after door has been locked and go to open door with fob in hand. Anyone have any suggestions? thanks for any help in advance

Hey guys hoping can get some input I picked my car up today after I had some issues with the eb tune on the supercharger basically needed replacement motor. Decided to go fully forged shop installed and installed blower and long tubes. Lund tuned it it drove great for 100 miles then check...

Looking for recommendations on where to get a forged long block with out a long led time any help is greatly appreciated

Hello guys, Here is the story I’ve been running the edelbrock stage 2 kit with their supplied tune for 3 months I recently had some vibration issues and brought it in. A compression test was done and found that cylinder 3 is running low. I’ve called edelbrock to get the warrenty process started...

Just like the title says using the edelbrock stage 2 kit with there tune has anyone broke anything in the rear end. I have these vibrations I can’t get rid of coming from the rear. Alignment is good, wheels balanced exhaust retightened. Only other stuff is from drop springs, rear drag springs...

Hey guys so I have a vibration in both the steering and seat. Wheels were balanced. Alignment is way off though toe is basically making wheels look like an hour glass. I have bmr front min drop springs and drag springs in rear with a stage 1 lock out hit. Car was driving fine for the longest and...

Hey guys getting ready to make the switch to the Lund tune for my eb stage 2. Lund says I need a 3.75 8 rib pulley check that but what size heavy duty belt do I need for fitment

https://www.dropbox.com/s/3jxseno8fhq7xfj/Video%20Oct%2019%2C%203%2055%2022%20PM.mov?dl=0

Hey guys I have a 19 gt convertible with a edelbrock and roush axle back and x pipe the left side of exhaust makes a shaking/ vibrating sound when you rev the engine is this like a loose clamp or something else wrong thanks in advance guys