Sponsored

Search results

  1. S550 Rear Differential Mount Bolts - ISSUES & RESOLUTIONS: Pics!

    Probably could, just never got around to it.
  2. S550 Rear Differential Mount Bolts - ISSUES & RESOLUTIONS: Pics!

    I did the through bolts on mine a few years back...Front and rear. At the time the inserts were not available, so dont have those. So far so good, but still a bit worried. Decent amount of track passes launching at 6K+ but still NA. Once the go I will do solid aluminum bushings and the through...
  3. Edelbrock S550 Mustang Pro Tuner Supercharger - 15899

    Could I ask why the 6 rib pulley system was included versus the 8 rib, or just not include the pulley system since it is a tuner kit. This Supercharger is on my short list, but I think I want the 8 rib. I see you offer a setup with the 8 rib already, but I dont have a need for the smaller...
  4. Inside power source for shift light

    I just purchased a MSD shift light for my 2015 GT and am looking for a switched power source to run the power wire to. I would prefer inside the car. Any good recommendations? Thanks.
  5. Switched power source for a shift light

    I just purchased a MSD shift light for my 2015 GT and am looking for a switched power source to run the power wire to. I would prefer inside the car. Any good recommendations? Thanks.
  6. 1st Gear Lock-out after new clutch and MGW

    My throwout and pilot bearing were replaced. My setup came as a package deal
  7. 1st Gear Lock-out after new clutch and MGW

    I’m currently running the Amsoil blend, but think I may give this a shot as well.
  8. 1st Gear Lock-out after new clutch and MGW

    I’m at about 1000 Miles and 8 passes on the dragsteip launching between 6500 and 7000 RPM so air should be out at this point. Other than the minor inconvenience, it’s not too big a deal. Will see if anything else comes of it.
  9. 1st Gear Lock-out after new clutch and MGW

    Is it doing the same thing in reverse as well? I just had my Exedy Mach 600 clutch installed as well. And if I come to a complete stop and put car in neutral, then try to shift into reverse it will not go in at all or if I do first it’s difficult. If I shift into another gear first then into...
  10. Those with a GT350 mani, what RPM are you launching at?

    MT82 cars on slicks. What is your launch RPM with the GT 350 manifold? Also what RPM have you found is the best shift point? Thanks in advance!
  11. GT350 Manifold Nitrous Setups.

    Any of you with the GT350 manifold running Nitrous setups? What units are you running and if you are running a plate setup, did you use the stock throttle body or go with the GT350 throttle body? Curious to see if running the stock TB if you just used the Nitrous plate and the TB adaptor...
  12. Steeda S550 Diff Bushing 12.9 Hardware Upgrade Kit

    Pretty much have to drop the entire subframe. Also good luck using a torque wrench on it. I gave up and switched to the BMR version with the upgraded through bolts front and rear. Takes a little more work and some modification to the differential housing, but it takes the stress off the bolt...
  13. GT350 manifold install writeup

    Been looking to see if there is a good step by step instruction written up for the 350 manifold install. In particular the routing of the vacuum hoses. It looks like JDM Engineering has a kit with instructions for $79, which is fine but they also want $20 to ship a few bits and a few pieces of...
  14. 44K Maintenance on 2015 Mustang GT Spark Plugs + 02 Sensors

    Were the bungs for the O2 sensors moved since he runs E85? Pretty well known that in the stock location that the Stainless Works/Stainless Power headers can have issues with the 02 sensors getting water on them and burning out due to E85 being hygroscopic. Angle the bungs on the front 02's or...
  15. Strut Tower Brace for Cobra Jet Intake

    Nope, and you will need to either lower your motor mounts, cut the factory hood or find an aftermarket hood to clear the back of the intake. Intake is too tall for the S550 without said mods.
  16. Reading logs

    Knock sensors are under the manifold. In the valley of the block.
  17. Viking Shocks - The PP "Bounce" is Gone!

    Reserructing an old thread. I just ordered mine, is the noise on the new ones still there? Also does anyone have a picture of the bump stop mounted on the top and what needed to be removed for install to get the bump stop on?
  18. WTB cloth rear seat bottom (black)

    Hello, anyone do a rear seat delete and looking to sell their rear seat bottom. My stupid clips broke when I was removing mine. If so let me know. Thanks. Black cloth only.
  19. Lund website says custom tunes out of stock?

    Unless prices are better when sales are going on, I don't understand why people don't just order directly from the source...i.e. LUND.


Top