Search results

757whp 2015 Ford Mustang GT Premium in Oxford White with 43,439 (Chassis) Miles. **(Complete Build List in Last 3 Photos)** This build is equipped with an RPG Stage 2 Gen 3 Built Short Block, that is paired with a P-1SC-1 on a 3.125” pulley. It’s fueled by a Fore Innovations L4 Dual Pump System...

I’ve been looking at upgrading my differential bushings and I’m unsure as to which ones to go with. I’m also looking for a through bolt kit. The car is mainly for fun runs on the street, ocasional casually drives, and I hope to take it to the track when I get some axels installed. Car is making...

Selling these used RTR Quarter Splitters. Asking $70. *Open To All Offers.* Currently dirty and have a little 3M tape residue on them but a quick wash with some scrubbing and they’ll look brand new (didn’t even have them on for 1,000miles). I will also provide all brand new double sided 3M tape...

Selling these used RTR Quarter Splitters. Asking $70. *Open To All Offers.* Currently dirty and have a little 3M tape residue on them but a quick wash with some scrubbing and they’ll look brand new (didn’t even have them on for 1,000miles). I will also provide all brand new double sided 3M tape...

Selling these used RTR Side Rocker Splitters. I’m wanting $170, but I’m open to all offers. Currently dirty but a quick wash and they’ll look new (didn’t even have them on for 1,000miles). I can also provide a small amount of double sided 3M tape to aid in the install. Fits all 15-17 Mustangs...

Selling these used RTR Side Rocker Splitters. I’m wanting $170, but I’m open to all offers. Currently dirty but a quick wash and they’ll look new (didn’t even have them on for 1,000miles). I can also provide a small amount of double sided 3M tape to aid in the install. Fits all 15-17 Mustangs...

I currently have the Steeda ‘IRS Subframe Support’ but I’m looking to replace it by either getting the BMR-CB005 Lockout Kit or the Kelltrac Posi-Loc System (Kelltrac claims the Posi-Loc System essentially performs the same function as the CB005 kit. So either get one or the other I’m assuming...

I currently have a 305/45/17 rear with a 275/35/20 up front but I’m looking to get some 18” front runners. Trying to decide whether to get the 26/6/18 or 28/6/18. So I wanted to see if I could get some personal opinions on the preferences.

SCT X4 Unmarried with 5 unlocks left. Asking $270 OBO Prefer local pickup (Dallas, TX); shipping is at buyers expense.

Set of 8 freshly cleaned ID 1000 injectors. 1 injector is bad but can be fixed. All others showed no problems when installed and ran great besides for the 1. Asking $400 OBO. Local pickup is preferred (Dallas, TX); shipping is at buyer expense.

This is a complete Magna Fuel Fuel System. Brand new triple hat with dual Walbro 465LPH E-85 capable pumps This fuel system is capable of 800whp. Asking $800 OBO Can part out if your looking for something specific within the complete system. Prefer local pickup (Dallas, TX), shipping is at...

Brand new, never installed. Asking $150 OBO Prefer local pickup; shipping is at buyers expense. Located in Dallas Ford Performance Oil-Air Separator; Passenger Side; Fits: 11-17 Mustang GT; 12-13 Mustang BOSS 302; 15-20 Mustang GT350

Brand new, never installed. Asking $150 OBO Prefer local pickup; shipping is at buyers expense. Located in Dallas Ford Performance Oil Separador; Passenger Side; Fits: 11-17 Mustang GT; 12-13 Mustang BOSS 302; 15-20 Mustang GT350

Was on my 2015 Mustang GT that has 40,000 miles. Good condition. Asking $85 OBO Prefer local pickup; shipping will be at buyers expense. Located in Dallas If you’d like more photos just pm me.

2015-17 Mustang GT engine cover. No cracks, chips, etc. Asking $85 OBO. Prefer local pickup; shipping will be at buyers expense. Located in Dallas.

Stock 2015-17 6R80 (Automatic) Driveshaft. Only has 40,000 miles on it, and in great condition. Asking $180 OBO. Prefer local pickup; shipping is at buyers expense. Located in Dallas.

I have a 2015 P-1SC-1 HO setup with a factory sized ATI Damper: 6.78”. ProCharger claims the limit of this head unit to be 65,000rpm. I’m wanting to know which pulley I should go with to maximize this head unit. I’m able to rev the car to 8,100rpm now and I’m trying decide between two different...

I have a procharger setup and I was wanting to see if there are any recommended catch can setup to go with. If any, please leave a link to the product as it would be much appreciated. Been looking at upr and motion raceworks products recently, just don’t know who or what to go with. Also if you...

I currently have a procharger setup that has the maf sensor located on the intercooler... I’m looking to find a new charge pipe that is compatible with a boss 302 intake manifold that can relocate the maf sensor location to the charge pipe and allow me to block off the original maf sensor...

Found a K-Member