Search results

That’s the same antenna I got. Looks like the ELM adapter should work. I got this one and it works great: OHP Ford ELMconfig USB device 500kbit/s ELM327 compatible interface with MS-CAN switch for Forscan FoCCCus Mazda OBD2 diagnostics...

Welcome to the forums! Post a pic of the new ride? :cheers: Come spring I'll be trying to make more shows up in Denver area, as well as occasional C&C event in Parker. I'd like to go to the Rocky Mountain Mustang Car Roundup in Steamboat again too (June). I went last year and it was a blast!

Super easy!! You'll just need the screen then, which you can get out of any Ford or Lincoln that has Sync 3, and the usb hub with adapter for the hub (make or buy). Then program it with ForScan software. :headbang: Too bad you didn't mention it earlier before working the deal with the...

Mine had the fan replaced but is doing it again too. Thinking of taking it in before my warranty is up just to give it one more shot to see if they fixed the quality issues with their motors, but I doubt it. Ford doesn't care enough about minor annoyances like this, apparently. A shame, but we...

Might as well. I was hoping they'd figure out the supplier issue at some point and get good ones in, but I was wrong on my first swap out. Might do another swap on it when I bring it in for the recall but I too will have to get it done before my warranty expires in January!

I'm betting it'll be a direct swap with some As-built changes. Hopefully the new DI engine isn't different enough to mess things up with the as-builts, though.

My bad, Hex, I deleted my post above because it was wrong information. I spoke too soon with out trying to actually bolt it up with the bezel! The Escape brackets ARE different after all. I tried it out yesterday and realized the holes are in a slightly different vertical location. So you can...

I can also say the Focus brackets are completely different, though the APIM and screen itself seem to be the same. Would just need to swap brackets if you get a Focus unit. Also it appears of doing an MFT swap you can just swap brackets from MFT to Sync 3 easily. Would only need to acquire your...

First, big thanks to Hextall for your help in this! Second, just letting you guys know that with a little searching around on Car-part.com, I was able to procure two Sync3 screens with nav APIMs from wrecked cars for dirt cheap! Searched around for a long time on eBay and everything was going...

While on the topic of throttle response. Any guys with manuals have any luck getting rid of rev hanging with Livernois tunes? I have both Lund and Steeda (some people on the forums said Steeda solved it...), but neither have been successful in getting rid of it. Neither seem to even tone it down...

It is a little intense at night, but by putting it under the factory plastic diffuser helps tone it down. I wouldn't say it is blinding as much as it is annoying, especially when I get stuck behind a car that has driver assist stuff and sets off the K-band radar alerts. I will usually turn off...

Here's the strip I used from Diode Dynamics. I got the 50cm strip and cut it about in half. You can still use the other half if you solder wires to it too :D https://www.diodedynamics.com/store/led-bulbs/led-strip-accent-kits/led-strips/flexible-5050-smd-led-strip-weatherproof

Check out my thread for those interested. It is a little different than what is being asked for here but could be relevant to some of you guys if you want to put in your own 12V LED array and control it outside of the CANBUS system....http://www.mustang6g.com/forums/showthread.php?t=90852

Final Product in use in the car :D Enjoy the tunes too! HA! [ame]

Here is the circuitry I used to get this to work with the Escort smart cable/detector. 9V LED IN is actually the LED wire from the Smart Cable circuitry. It is the black cable, which I soldered to directly on the PCB in the Smart cable box. I also added a switch so that I can disable the LED...

So I wired in an Escort radar detector to my car, and found that during top-down driving, especially in daylight, I was missing radar alerts due to the wind and/or radio noise. I thought, man, I'd love to get a HUD to alert me of radar alerts! Nice thing is that Escort's smart cable (both...

You will have to create a log in for the site first, then go back to the link once logged in. Then it will bring up a box for you to put your VIN in. :cheers:

Here's the thread. Its a little intimidating at first, but it was real easy once I followed the instructions and got through it the first time. I was also able to change some other things which was very cool. Plan to change the stupid setting that blocks the input of NAV while moving too but...

There would be, but would require re-wiring the foglights and likely to a typical manual throw switch. Not really worth it when you can program it to do what I was looking for with a $30 cable from Amazon and free software on my laptop :D

In Colorado Springs, I've heard good things about Revolutions performance as well as EDP (they specialize in turbo applications). I haven't used them yet but plan to talk to Revolutions about tuning my 2015 GT as well as my friend's V8 Miata project I'm helping him with.