Sponsored
80FoxCoupe's latest activity
-
80FoxCoupe replied to the thread Crank pulley starting to come off..What type of hardware was holding the balancer on when it walked off? -
80FoxCoupe replied to the thread Crank pulley starting to come off..What hardware was used when the balancer walked off?
-
80FoxCoupe replied to the thread Crank pulley starting to come off..The only difference I've seen in 2011-2024 coyote crankshafts is bobweight.
-
80FoxCoupe replied to the thread Crank pulley starting to come off..This balancer was not properly installed which led to the snout failure.
-
80FoxCoupe replied to the thread Crank pulley starting to come off..Just throw a crank stud on there, Kinetic or FFRE and call it a day.
-
80FoxCoupe replied to the thread GTD in the wild at Costco.Everyone needs fuel and a 5gal drum of mustard!
-
80FoxCoupe replied to the thread Aisin Water Pump.PP rad, 170 stat and gt350 pump here. No issues but just street drive and drag race.
-
80FoxCoupe replied to the thread Aisin Water Pump.I hear ya. Things happen I suppose, but put mine through more abuse than most and so do my pals. Yet to see anything outside of a seal...
-
80FoxCoupe replied to the thread '16 GT, sleeved Predator and F1A94.Made a few 660 hits in the fall but broke a cam cap. Be back out soon!
-
-
80FoxCoupe replied to the thread '16 GT, sleeved Predator and F1A94.I put a v3JT on the truck and pullied down a bit!
-
Yea come on! UPDATE UPDATE UPDATE! hahaha
-
80FoxCoupe reacted to Strokerswild's post in the thread '16 GT, sleeved Predator and F1A94 with
Like.
Probably working on that truck again. For which we should also have an update. -
80FoxCoupe replied to the thread BL Fabrications 88/96 turbo install on 2019 Bullitt.You are doing great work @NGOT8R !
-
Been a while since I've last updated this thread. Been so busy with other things. Currently in the middle of building a workshop and...
-
80FoxCoupe replied to the thread Aisin Water Pump.I hear you, but have never seen those issues with coyote water pumps.
-
80FoxCoupe replied to the thread Aisin Water Pump.I didn't not notice any CHT difference on the mustang. It's possible recovery time after pass was quicker but ive never looked for that...
-
80FoxCoupe replied to the thread Aisin Water Pump.Typical coyote water pump failures are simply seal failures leaking out of the weep hole. I have Def seen impeller issues you described...
-
Not sure of it's exact composition, but for sure it isn't the same material as the shaft that it is pressed on to. The expansion and...
-
80FoxCoupe replied to the thread Aisin Water Pump.Do we know if the oem units actually have a plastic impeller? Seem like a ceramic material to me.
-
80FoxCoupe replied to the thread Aisin Water Pump.I was hoping there were some performance metrics than could be referenced. I have not seen any durability issues from the oem impeller...
-
80FoxCoupe replied to the thread Aisin Water Pump.Why do you think the aluminum impeller is superior? What data do you have to support that theory?
-
80FoxCoupe replied to the thread Will earlier Gen Coyote block work with Gen 3 heads ?.Run the head gasket that works with the cylinder bore. Shoot for .030 to .060 larger than cylinder bore. Also ensure that the oil feed...
-
80FoxCoupe replied to the thread Engine rocking aggressively.You gt350 guys are an emotional bunch.
-
80FoxCoupe reacted to RNM's post in the thread 2026 Dark Horse SC Mustang (S650) Pricing Released with Like.
A fool and his money are easily parted.
-
The AWD Mustang Project has been sort of on the back burner the last few months while I focused on some house projects. Goals for this...
-
80FoxCoupe reacted to beefcake's post in the thread RSA Race Solutions Built 10R80s Now Available At Beefcake Racing! with Like.
🔥 RSA Race Solutions 10R80 Builds 🔥 When it comes to serious performance, RSA Race Solutions takes the 10-speed transmission to...
-
80FoxCoupe replied to the thread What do you run for oil?.Aka Mega knock.
-
80FoxCoupe reacted to NGOT8R's post in the thread BL Fabrications 88/96 turbo install on 2019 Bullitt with Like.
Small update for today. About 3 weeks ago, I came to the realization that my PCM mount wasn’t going to work, as the PCM harness simply...
-
80FoxCoupe reacted to masonhoare9's post in the thread BL Fabrications 88/96 turbo install on 2019 Bullitt with Like.
Pretty much all i have left is plugging some connectors back in, moving two grounds on the wiring and running the o2 sensor and put the...
-
I've had great luck with the Jeep Grand Cherokee Hemi. I had a '20 GC Summit Hemi with the air suspension that worked great, no...
-
Much depends on the trailer you intend to tow. Even a 1/2 ton pickup could be dicey if you're hauling a large heavy enclosed trailer...
-
80FoxCoupe reacted to wingnutt's post in the thread First Start E85-16lbs Smoothboost & IW with Like.
devils advocate here…but maybe just buy a centrifugal instead, and not need all the accoutrements to make it act like one 🙈🙉🙊
-
Im in australia. But I got my Darton sleeves from Brian crowder in the USA for $1100 usd. And Machining and fitment here in Oz was...
-
80FoxCoupe replied to the thread Piston Sleeves?.Sleeve install itself is around 2200. If you have the ability to have the machine shop assemble the shortblock, and you do the rest some...
-
80FoxCoupe replied to the thread Engine rocking aggressively.I know your comment had an elitist tone to it that was intentional, but trying to flex on me is laughable. But you are right I have a...
-
80FoxCoupe replied to the thread Engine rocking aggressively.Relax, nobody is taking shots at anything. It's just a mustang I don't see what the big deal is. Weird how that upsets you so much. Pull...
-
80FoxCoupe replied to the thread Engine rocking aggressively.Get over yourself, it's just a regular mustang. Not sure why you are getting so upset about it. Get those emotions in check kid!
-
80FoxCoupe replied to the thread Engine rocking aggressively.If I don't agree with you the response is anger. Use your words child.
-
Straight to the ignore list, what an ignorant comment to add to this thread. Almost certainly riding around on D all day, too, and mad...
-
80FoxCoupe replied to the thread Engine rocking aggressively.I mean it's not anything special. Why does my opinion upset you? It's just a mustang variant, one of many. I suppose if I don't see it...
-
80FoxCoupe replied to the thread Engine rocking aggressively.There alot you dont understand. Just calling it like it is. Call it whatever you want.
-
80FoxCoupe replied to the thread Engine rocking aggressively.It's different from a GT as a GT is different from a V6. But make no mistake, it's just a regular mustang.
-
lol…does my first wife count?
-
80 thousand on mine, 20 thousand boosted and I drive it EVERYWHERE 😉
-
80FoxCoupe replied to the thread What’s better Boss 302 or a GT350?.I wouldn't consider either one has much car show cred, but I suppose I'd take the gt350. Superior in every measurable metric.
-
80FoxCoupe replied to the thread Dynoed my Procharged 5.2L build - four year process....You are 200hp away from max blower rpm.
-
80FoxCoupe replied to the thread Dynoed my Procharged 5.2L build - four year process....What pulley on the blower?
