What did you do to your GT350 today?

[Tribefan]

I am not a big fan of bolt on adaptor spacers. I did install longer studs ( Ford F350) in order to run these spacer.

Btw, 5mm is max you can go with factory studs.

This is what you want as far as bolt on.

http://www.motorsport-tech.com/wheel_adapters_pop_car_d3

Thanks for the info. How involved is it to put longer studs on there? And did the front spacers bring the wheels close to flush with the front fenders or are they still pretty inset?

Sponsored

 

[Niz55]

Thanks for the info. How involved is it to put longer studs on there? And did the front spacers bring the wheels close to flush with the front fenders or are they still pretty inset?

Super easy to install the studs.

They are much closer to the fender but I think 15mm will make it nice and flush.

 

[Niz55]

This is what happens when you run max caster 8.2+

Going to lower it to 6.7

 

[Phenom5.0]

Wrapped a few interior parts today with carbon fiber. I had a small defect on the dash from the previous owner putting a cell phone mount and when I pulled it off it slightly bubbled the stock plastic. This was an easy way to cover it up.

 

[Niz55]

Wrapped a few interior parts today with carbon fiber. I had a small defect on the dash from the previous owner putting a cell phone mount and when I pulled it off it slightly bubbled the stock plastic. This was an easy way to cover it up.

Is the wrap vivvid brand?

 

[Phenom5.0]

Is the wrap vivvid brand?

Yes with the air release tech. I had 2 rolls of it on hand. Hopefully it holds up I'm liking it.

I may end up doing a few more interior peices like the radio bezel and door handle trim.

 

[Niz55]

Steeda drive shaft loop painted blue. I must say, this is very very high quality loop. Very sturdy.

Thank you @tj@steeda for discount code.

 

[Niz55]

Yes with the air release tech. I had 2 rolls of it on hand. Hopefully it holds up I'm liking it.

I may end up doing a few more interior peices like the radio bezel and door handle trim.

i might get the carbon epoxy wrap.

 

[Phenom5.0]

i might get the carbon epoxy wrap.

I actually have a piece of the high gloss cf wrap but it wasn't enough to do the entire dash plus the passenger side piece.

I may change it down the road to the darker more glossy wrap but it's easy to remove and not terribly hard to wrap (my first time wrapping).

 

[jgallo41]

Got some fresh tint today.

 

[A_Bau3]

Got some fresh tint today.

What company and % did you go with? Looks good and not too dark.

 

[Zitrosounds]

Loaded on trailer heading home from Road ATL

 

[loco_GT350]

Wrapped a few interior parts today with carbon fiber. I had a small defect on the dash from the previous owner putting a cell phone mount and when I pulled it off it slightly bubbled the stock plastic. This was an easy way to cover it up.

That came out nice. I have always thought the interior of this car would look much better with some carbon fiber interior pieces and your wrap is confirming my suspicions. How hard was it to do? Now you go me thinking that maybe I will consider doing something like this.

 

[Phenom5.0]

That came out nice. I have always thought the interior of this car would look much better with some carbon fiber interior pieces and your wrap is confirming my suspicions. How hard was it to do? Now you go me thinking that maybe I will consider doing something like this.

It was my first time. It's not perfect but I'm really happy with it.

It wasn't really that hard, I looked up this video


And the only difference is that ours has the extra gauges in the middle.

If you do it mind the notches around the AC vents. If they are covered at all with the wrap they don't like to install back in.

 

[TaraFirma]

Pics on the way home from work the other day.

Sponsored