Search results

Hi everyone I need some help. My car got the hood replaced after a accident and swapped from the np concepts hood to the iKon hood (gt500 style for both). The mp hood fit great but rubbed the crap out of the wiper and the iKon hood is now doing the same but to a lesser extent but from my forum...

So a bit back I had Drivers door Drivers fender Front bumper Hood Passenger fender Repainted. Obviously not perfect as it has some fisheyes and defects but it's a daily driver. Now due to some damage in looking at needing the Passenger fender Passenger door Passenger mirror Passenger quarter...

So I'm just outside of Philadelphia Pennsylvania about 50 min to get to the center but I'm willing to drive if it's a good shop. I'm trying to stay skmewhat on a budget and get my 2017 paint corrected and ceramic coated. (Clearcoat is chipping off pass ever door at edge but I think ceramic cost...

So I had my windshield retinted today and I'm wondering about the best way to approach this. I have a few issues 1, weird mark like a bubble rolled over/scratch/wrinkle maybe? 2, (circled in blue) a very small spot that looks like brown something for trapped under the film. 3, an absurd...

These are smoked taillights for 15-23 but straight bar style that came on 15-17. This set pictures has peeling clearcoat mostly contained to the drivers side light. They work without an issue (included a photo with them lit up). Reclearing is always a option as is vinyl to hide the peeling or...

Fresh off my 2017 mustang gt, RTR lighted upper grille. Goes for 600 new with lights or 220 new without lights. The lights are removable with 3 screws each which can't be seen when installed. So run it with lights (one side has a couple bulbs along the bottom out which is common for the lights)...

Red vs Tinted vs Smoked taillights on a black car. IMAGES HERE Looking for some insight on taillights. My renegade/winjet lights are peelingand possibly separating on the edges not sure how bad. I went back and found my oem lights (they have a weird film applied which is shown in the one...

So I have a 2017 mustang gt. With a quality J&L catchcan. After doing some hard pulls I found out I burned/lost almost a full quart of oil (no leaks or puddles, no visible leaking from valve covers or on the underside of the hood). I've never ever seen or had this happen before. Catch can was...

Had some fun coming back from the shore for the 4th of July weekend tonight (and my birthday) and I drove it hard. 1st to 5th shifting at 6500,7000 rpm and (now tell me if I just can't drive for shit I won't take offense) I'm just dumping the clutch as fast as I can at those higher rpms and it...

Urgent because it's LOUD. hear it clearly over the radio at moderate volume loud. And I'm about to go for a 3 hr trip and I can't stand to listen to the noise for that long let alone the 3 hr's home Today out of nowhere this sound popped up and now it won't go away. Nothing at idle but once...

While under my car to try to fix a broken bolt I noticed a large amount of rust for a 2017. Differential and rear subframe have surface/flaking rust. Angle that holes the evap below the spare tire well is at the point where it crumbles to ashes if you touch or push on it, rear bumper brace and...

ATM I have a rtr light grill on my 2017. And as is typical with rtr the product is failing (low quality junk). And the lights are going out little by little. So I'm trying to figure out my next step and I can either remove the lights and run the rtr grill with no lights (not terrible but it also...

So during a very painful driveshaft install attempt (failed) I unbolted and dropped the trans crossmember all the way down to try and get a better angle. But after following the instructions to reinstall, jack up, start bolts, remove jack and then tighten up. I've noticed it's shifted over the...

Hey y'all, prepping for when my dss aluminum driveshaft arrives for my 2017 gt pp. I see that the one end does not have enough space for a socket so should I just wrench it till tight or order myself a set of crows feet so I can properly use a torque wrench and set it to spec? Also dss claims...

This would be a short term thing 1 month max. I live on a hill and street park. My ebrake cable just snapped for the driver's side and the passenger side cable doesn't look too good either. Will only using first gear to park hurt anything or should I go buy a brick to toss under one of the tires...

So I did the rear calipers recently and I noticed one of the banjo bolts is leaking slowly on one side (I'm presuming it's from the flat piece where the copper washer goes is currently super rusty and yucky. I ordered a new set (assortment of sizes) copper washers off Amazon some random 325...

Disregard

There's 1 singlular thread that even mentions this item and it died off with no useful responses. Does anyone here have this or know about it? Under 700$ for a brand new aluminum 1 piece driveshaft. From what I know dorman is reputable and make oe quality parts but this is the first I'm seeing...

Should I even attempt to fix this? During my thermal exhaust install i broke this piece off (yes im an idiot and used a string though it to support the midpipe of the exhaust I didn't realize it was held on by basically nothing). Should I leave it off and forget about it, open up the holes so it...

While cleaning my car today after getting it back from the collision shop I noticed the passenger door has a large amount of chipped paint. Some through to primer/rusting and the rest looks like clearciat missing? Will this get worse and if so what are the best ways to repair it? Vinyl decal of...