Search results

Nope, its a replica. Prices were all over the place but I ended up getting one around the 1200 mark from one of the more reputable looking shops on ebay.

I ordered one of those s650 take off sets and its not going to just be a simple swap over. I installed the bottom of the drivers seat and stopped. There were some minor differences on the clips outer clips, and the inner velcrow was different, s550 has velcrow running all the way parallel with...

Its a little torn apart right now, but I did find a couple of older ones showing it right after it was painted and installed for better reference.

I can confirm this, I have an 500kr Hood and it clears the gen 5 whipple with stock motor mounts. The closest spot is at the rear of the center vent as the whipple extends further back than the vent. Going off feel theres around .75-1 inch of clearance. I dont run the rain trays but it would...

Currently setup to run 75 EOI, but there is some other logic I'm running into that is limiting me. I originally though it was due to dropping fuel pressure but now that has been resolved I'm still seeing DI DC lower than I'm requesting. I might have to pick your brain at some point on the DI...

Thank yall for having that available, Saved me a ton of time and work. Fixed the P0463 code, I updated my post. Interesting on that 10 second ramp down, Before I switched my focus to this project I was working on dialing in the GDI side specifically trying to make sure it is fully utilized and...

Finally had some time to work on this project. Got the harness all put together and its working great on the fuel demand side. I need to start digging into the tune side as a quick WOT test without changes was around 10-20 psi over desired fluctuating wildly and had hit around 110 with 73...

I did the 72 Hour approach myself and used this tool to download everything for my vin. Service manual, wiring diagrams, Connector pinouts. If your somewhat technical it can be used to pull everything for your vehicle as pdfs in a folder structure, There is also an html flag so you can get it...

I sent in the throttle body. They didn't explicitly say what they did, but looking at it when I got it back there was a small paint pen mark near the adjustable set screw and it was filled in so it was no longer accessible. So I would assume they did some kind of adjustment or calibration on it...

I had to do all four of the vct/vvt solenoids pretty early on well before the whipple went on. But my primary symptom was a surging/bouncing on its own when idle for 5-10 seconds before recovering or stabilizing, sometimes small rpm swings but sometimes large. It would stall if the surging was...

That's is definitely a simpler and more elagant approach. I sent a dm, I'll take one if available. I'll still probably give mine a try for the giggles but yours looks to be a better long term solution.

I did some digging on the dual FPDM with diagnostic response. It doesn't look bad at all. Should be able to be done with raw hardware, or microcontroller based if desired. Supposedly the signal from the PCM to the FPDM is just PWM, The diagnostic response back to the PCM is also just PWM...

Sounds exciting! Some parts have started arriving, I managed to find a take off 22 gt500 assembly but it has a different part number than your post. Still waiting on connectors but Ive also found a github project to automate pulling the service manuals and wiring diagrams from fords service...

What great info. I'm beginning to play with e85 on the tuning side and recently started pushing over edge of the dw400 + bap. I was seeing a drop in pressure around 5-8 psi below commanded on the low side and was wondering why I wasn't seeing any signs of it in the wide bands. I had assumed it...

I am going to give this a try, I would definitely appreciate any additional info that you would be willing to share about the base conversion harness, tuning, venturi adjustments, and dual FPDM hardness. Are you leaving your BAP in the mix with this? I had planned on switching mine over to the...

I payed 3500 for a whipple stage 2 w/ with the oversized exchanger + opg install; All the quotes I got where right in that same area.

There are a few swirl hotspots to be super careful with I only touch them with new microfibers: The gloss plastic used on the rear decklid and around the tail lights is EXTREMELY easy to swirl, its also used on the front grill. Also be careful with the top section of the front bumper between the...

Im not an expert so feel free to chime in but this is what I see. Gt350 intake manifold, looks like a stock airbox (Maybe a 2018? Im not sure they make a mishi tube for the 18+ yet), injectors (basically required to run the 350 mani and I would be wiling to bet it has a flex tune), gt350...

My first mustang was a MY12 kona with the factory white stripes; One of the best $475 I've ever spent on an option. I owned the car for 7 years (car was not kept in a garage) never had any peeling or discoloration that couldn't be cleaned off. I always found myself staring when it was within...

Take a look into VCT Solenoids. https://www.mustang6g.com/forums/threads/idle-goes-rough-randomly-stock-tune.133398/ A few members including myself had random surging idles and or randomly stalling out completely.(It typically reared its head when coming to a stop) It would typically drop to...