Search results

Buy in store. There £1029 on Costco website. went I store and it was £960 inc vat.

Bought a Quickjack from Costco today to make working on the car easier and quicker. No more trolley jack and stands. It runs from 12v supply so either from the car you are lifting a spare battery so it’s quite mobile. will also be handy for the Westfield too.

Yes as it fits between the grille and air box intake Passage way. It will only fit the standard grille though as far as I’m aware. I fitted this to help reduce backwash from the rad at low speeds and in traffic.

@Manders Mustang Not that i'm aware of. Edelbrock use a modified Airaid CAI box and just open up the hole to fit the larger MAF body in. So the carbon trap will be the there for standard cars too. I was going to remove it yesterday but just forgot lol. I'm working on the car this morning so...

Had a few bits arrive yesterday and had an hour spare today so cracked on firing a few bits. first up was a Velossa tech big mouth. Since supercharging the car and going stage 2 I have been getting higher IAT’s. I decided to refit the standard grille but swap the chrome badge for a gloss pony...

You can buy mine for 40k, makes it a bargain.

Bought this kit of eBay https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F401678848988 the motors are the same shape and bolted right on giving me remote control of the valves for on/off. It wasn’t straight forward as the spring between the motor and valve...

I used this kit https://www.ebay.com/itm/2-SETS-2-5-INCH-63mm-Vacuum-Exhaust-Cutout-Electric-Control-Valve-Kit-With-Pump-/183717235938 The motors fit the 18+ Perfectly. The only thing I had to do was tack weld the spring to the butterfly valve side as it didn’t line up with the groves. You...

The car in the vid is quoting flywheel so about 680whp. That’s very realistic. Again go read Geiger's own website. My car spec is above. Can’t remember timing but had no knock on the power runs. Also the car in this vid was on 93. It’s a member on here. He did eventually snap his crank but it...

Not really no just bits that I have posted. the spec is quite straightforward. 16 GT Manual Edelbrock 2300 supercharger kit Edelbrock cold air intake GT 350 throttle body JMS BAP 2.75” pulley Boundary OPG & CS Stock exhaust except 18+ Ford active back boxes. some rear subframe parts from...

My car is tuned by Rob Shoemaker at Palm Beach Dyno and he knows his stuff. I’m at 12psi (valves open, 14psi valves closed, gives you an idea of the restriction in just the back boxes) and according to Rob high 600’s is possible with headers/cats on pump fuel. There are plenty of cars about at...

Don’t think it’s WHP. More likely flywheel figures so about 680 wheel. I’m at 640whp and still on standard headers and exhaust. Some long tubes and high flow cats will get me up at the high 600’s so it’s realistic.

My 16 UK GT

The supercharged cover is hitting the K brace.

Yes it came with single tip. the car has the Roush valance fitted to accommodate the quad tips.

I have a 18+ active axle back on my 2016 GT. just had to cut the old section off just near the resonator. only issue is the valance, I fitted the roush one.

Saw a Bullitt yesterday going into Newmillerdam around 3/4 pm.

Just gone 3 years old and 50k miles.

Bucket of water over it.

Bought and fitted the BMR cb762 kit to the rear subframe. Took about an hour to get done. Haven’t had chance to drive the car yet though. Bought some 72lb injectors a few weeks back also from a US member on here but for got to order some top hats. These finally arrived today so will be...