Search results

Nice write up. How did you install the center/footwell discharge sensors? Did you have to drill a hole and glue in place or is the mounting hole available just covered up with a plastic plug

How's your salvaged GT350 going?

Checkout the link below. This is how I got power to my seats. https://www.mustang6g.com/forums/threads/upgraded-to-power-seats-on-base-s550-surprising-solution-found.108075/

I'm assuming that the ACM is from a 2020 mustang. All 2020 and newer Mustang ACM's are using the SiriusXM radio. Prior years ACM used the Sirius radio. These newer SiriusXM radio include the 300+ channels. I have a 2015 mustang which has a Sync 3 upgrade. Wanting the extra SiriusXM 300+ channels...

I'm experiencing the same issue. What works for me is to perform a Sync soft reboot. Press and hold the Seek Up (>>I) while pressing and holding the power button for approximately 5 seconds. Sync will reboot and Sirius will work again. From everything I've read this is bug in the new Sync update...

Installed leather seats into my 2015 v6 about 6 months ago. Enabled heating and cooling using the info from this thread. My seats came with the memory module (DSM), so I finally completed this as well. Everything is working, but I'm getting two DTC's (C1B15-Sensor Supply Voltage-B-, and U2010...

Installed leather seats into my 2015 v6 about 6 months ago. Enabled heating and cooling using the info from this thread. My seats came with the memory module (DSM), so I finally completed this as well. Everything is working, but I'm getting two DTC's (C1B15-Sensor Supply Voltage-B-, and U2010...

Here is a link to enable the heating and cooling functions: https://www.mustang6g.com/forums/threads/how-to-enable-heated-cooled-after-swapping-from-base-to-premium-seats.129230/ I have a base V6 2015 and using both of these threads I installed leather 8-way power seats, and enabled the heating...

This link will answer all of your questions: https://www.mustang6g.com/forums/threads/how-to-enable-heated-cooled-after-swapping-from-base-to-premium-seats.129230/ This link will help with power seat install...

Yes, they are different. I too would like a adapter harness for the new B&O 12 speaker amp.

I have purchased a 2020 HD SIRUSXM (300 channel) ACM. It's my belief that the new ACM won't play with the older shaker amp. So I'll have to install the 12 speaker B&O amp for everything to be happy. My concern was with the B&O speaker ohms requirement. If I install the B&O my shaker 2 ohm mid...

Thinking about installing a 12 speaker B&O amp from a 2019 mustang. I currently have a 12 speaker shaker system where the speakers are 2 ohms, tweeter 8 ohms. Hoping I don't have to replace all of the speakers.

From the listing link above, It appears to be talking about the screen only. If you need both the screen and APIM contact the seller before buying.

PM Sent

I'm interested in the 2020 HD ACM. Can you provide pictures.

NC GTier, I'm starting my cloth to leather seat swap. The leather seats I got have the memory module on the drivers side. I would like to enable the memory seats feature. Looking at your memory parts list above can you share what connectors are needed for the DDM and memory door switch.

I'm ready to swap my cloth seats to leather. The seat power connector on the passenger seat does not have power or ground wires. Since I'll need to run power from the grey kick panel connector (and ground) to the seat power connector, I was hoping someone knows the part numbers for the...

PM'ed

Were you able to figure out how to clear the airbag light and the occupancy sensor error? I'm thinking about replacing my cloth seats with OEM heated and cooled leather seats, just worried about airbag errors. Hoping Forscan can do the job.

What is the difference between sync 3 touchscreen (18b955) -SA and -SB. I found a 2019 Fusion APIM Sync 3.3 that was connected to a -SA screen. Can I use a my -SB screen instead?