Search results

Check throttle blade angle with key on. You will need a scanner that can read that. Mine was out of spec, reflased the tune, problem solved.

JBA’s fit great. The quality of the long tubes were better than I expected. I was able to use all of the factory studs, did not have to remove the frame mounts and no contact with the steering,A/C Block or frame. I think the are way under rated. The install wasn’t hard just time consuming. I...

I did some 5 gear pulls from 2k to eventually 7k WOT Knock pull .5 degree at 6-6500 all other RPM 0 or Added timing. Lambda showed .75 at 7k MAF was about 80. This was using pump 91 and Torco. I’m not looking for Max Power, Just Safety. Do these seem about right? I’m getting the pieces to go...

Just added JBA Headers and full Exhaust to my 2018 GT A10 W/Stage 2 Edelbrock running canned EB 91 Pump Gas tune. When first installed them, I got the PO420/PO430 Codes. I added spacers to the rear o2's and no more codes. I've always throw some Torco Accelerator in the tank as Pump 91 in Phoenix...

I’m in N Mesa,Gilbert Rd./ 202 Red Mountain area

This made me turn on the Way Back Machine. First Ride Moms 1968 Notch Back (1978) First Car 1966 Mustang 2+2 Fastback Black(1979) Second 1968 Shelby GT350(1980) Third 1970 Boss 302(1980) Fourth 1966 2+2 Fastback 427 SOHC (1982) Fifth 2006 GT (2010) Sixth 2012 GT MT82 Paxton SC(2013) Seventh...

Looking for a complete set of stock cams for a Gen2 5.0 I Purchased. The previous owner kept his aftermarket cams and thru away the stock cams. email or text me @602-738-5196 Thanks,Mark

Thanks

What bias should I be looking at?

The car went 160.5 at last weeks No Fly Zone 1/2 mile event, on the 93 Edelbrock tune. Beat my buddy’s HellCat by 5 MPH. The warranty will be up next month so thought I would try the headers.

SCT LiveLink. I know I need to monitor AFR. Just didn’t know if the wide bands will compensate for the Headers. I’m putting together a fuel system to go E and will have Shaun @AED Tune it in the future. I have the Headers on the shelf and want to try them.

Hey Guys, I’m currently running the canned Edelbrock Stage 2 93 set up on my 2018 A10, Runs Great. The only other mod is a 3” Catback. I’m adding long tube Heades with high flow Cats. What should I look for in the Data logs to determine if it needs a Custom Tune?

I’m in Arizona, it’s a little cooler than normal, will be 65- 70 degrees this week. I would be happy to test one. I have gone through 2 of the plastic POS bottles. With the plastic bottle I’m afraid to tighten the cap to where it should be. PM me, if you need a test Mule.

Intake Sold!

There is a station not to from my house on Broadway and Val Vista SW corner, that sells E85. I spoke to a guy with a Nissan GTR filling up there, he said it is good quality. I have not tested it myself. Im not sure of other stations, Apache Sands on Main and Sossaman used to have E85, There may...

Intake Manifold $250 + Shipping Air Box with intake Tube $100+ Shipping. Damper $150+ Shipping. Engine cover ? Fuel rails and injectors Free with intake purchase.

Thanks for the info, very helpful. I'm going to pull the trigger on the X2 setup with their 400 pumps should be enough for my needs. I have a 18 with DI. I like the idea of the pumps running all the time vs staging them, if the e85 will keep them cool, less to go wrong and lean the car out.

Good write and Photos. Looking to do a similar Fuel set up on my 18 to go E85, its the Stage 2 kit and here in AZ we only have 91. The Edelbrock CARB certified tune runs like crap so I would like to get it tuned. I know there are ports on the top side of the rails for the stock fuel lines to...

Still available?

I had the same issue and just drilled the holes slightly larger. There is plenty of material around the bolt holes. If you look at the Factory intake the bolt holes are Huge, and you can move the intake Bolts around. Edelbrock should have made these larger from the start. Just make sure all...