What is the widest tire size you have used on your S550 Mustang? Share info & images

[08StangGT_CS]

Hello the 325/30 should not need any camber.
Here are a few images of this setup with no camber:

The 345/30 with a -2 would set perfectly flush.

Does it make a difference on the 345 if the rear is only dropped half an inch?

Sponsored

 

[MrWolf]

Hopefully I get them mounted tomorrow. Didn't get a concrete answer but heard - 2 from Paul so that's what I'm going with. I'll let you know once they're up on the car.

Salivating at the thought of seeing these

 

[SienarSystems]

[MENTION=11685]Need4SpeedMotors[/MENTION] - thanks for the killer wheels and great support! I’m going to go with factory specs for the alignment and when the rears are done may go to 345s and -2.

 

[Need4SpeedMotors]

Does it make a difference on the 345 if the rear is only dropped half an inch?

Not much of a difference on BMR?
Check out this GT on 345/30 Rears. 19x11 Eibach Pro kit.

 

[Need4SpeedMotors]

[MENTION=11685]Need4SpeedMotors[/MENTION] - thanks for the killer wheels and great support! I’m going to go with factory specs for the alignment and when the rears are done may go to 345s and -2.

No problem, Thank you for the feedback and support as-well.
Can't wait to see those 345's!

 

[blessthecoyote]

No problem, Thank you for the feedback and support as-well.
Can't wait to see those 345's!

is it possible to run 345/30/19 like the white s550 if lowered on eibach sportline 1.3''

 

[BluePonyGT]

Hey this might be OT since it's not a fitment question, but I've noticed over the course of this thread different center caps to the Project 6GR wheels. The branded ones, but also ford, pony, etc. What center caps will fit with these wheels?

 

[Need4SpeedMotors]

is it possible to run 345/30/19 like the white s550 if lowered on eibach sportline 1.3''

Sportlines would be to aggressive and might have some rubbing.

 

[Need4SpeedMotors]

Hey this might be OT since it's not a fitment question, but I've noticed over the course of this thread different center caps to the Project 6GR wheels. The branded ones, but also ford, pony, etc. What center caps will fit with these wheels?

Correct the Project 6GR wheels accept oem center caps.

 

[Streetcar]

SO a 325 with around factory camber will work on a 325 tire 20x11 or 11.5 with sportlines?

 

[Bybcous]

thanks, I didn't know if you could use standard 2016 GT lug nuts with those wheels.

No i ran into this problem 1 hr before shop closed and my tires were mounted. I gotv 14x1.5mm from autozone in acorn, tapered seat for 7.99 for 4 lug nuts, so abiut 30 total after going to 4 different autozones to find enough nuts.

 

[Streetcar]

Not much of a difference on BMR?
Check out this GT on 345/30 Rears. 19x11 Eibach Pro kit.

On sportlines could you run a 325/30r20 with factory camber ? Also what offset on the car with the 345s and any reason you didn’t go with the 11.5 wheel?

 

[Digital_Synapse]

Autocross was last weekend, back tires stuck great but the fronts I think are too skinny. Car just didnt want to turn, on or off the gas.

I ran the same tires on my last Mustang and the turning was much more responsive.

If you dropped the rear to match the front it would turn, or bumped up the front to match the rears. The balance was too lopsided. You're going to have crazy push or understeer. That setup is for drag racing, if you want to turn you want to have roughly the same front and rear setup, ie square. I was running 295 325 f/r and I had push, next set of tires is going to be 305 square.

 

[HoustonGT]

Vossen VFS-1's, 20X9/20X10.5 with Continental Extreme Contacts. Fronts are 225/35 rears are 315/35's. No rub even dropping front only 1.5"

Are you lowered or stock?

 

[HoustonGT]

Hello Members,

Here are some pictures of a customer as promised sporting
Project 6GR Seven Satin Black 19x10 19x11
Nitto Invo 285/35/19 345/30/19

Fitment is spot on...​

Lowered or stock?

Sponsored