Sponsored

Media added by REDHRSE

Navigation

  1. Example Category 309
Browse albums

Most media items

  1. Tomster
    359

    Tomster

  2. raiderjatt02
    333

    raiderjatt02

  3. DarkSubRosa
    297

    DarkSubRosa

  4. klumpikat
    296

    klumpikat

  5. Norm Peterson
    265

    Norm Peterson

Media statistics

Categories
1
Albums
2,726
Uploaded media
16,198
Embedded media
3
Comments
231
Disk usage
3.9 GB
side view

side view

  • 0
  • 1
as you can see it is not touching the care. due to the strength of the steel it will not touch the body. its angled at a pleasing angle

as you can see it is not touching the care. due to the strength of the steel it will not touch the body. its angled at a pleasing angle

  • 0
  • 0
this the plate installed

this the plate installed

  • 0
  • 0
this is the bracket mounted

this is the bracket mounted

  • 0
  • 0
mount your bracket. if you have small hands GREAT because you will have to squeeze your hand through the small openings in the lower grille to put the

mount your bracket. if you have small hands GREAT because you will have to squeeze your hand through the small openings in the lower grille to put the

  • 0
  • 0
once you have grinded and smoothed all of the burs, paint the bracket. this must be done well so it does not rust. then place 3m body panel adhesive

once you have grinded and smoothed all of the burs, paint the bracket. this must be done well so it does not rust. then place 3m body panel adhesive

  • 0
  • 0
once complete it should look like this

once complete it should look like this

  • 0
  • 0
take you angled steel and evenly hammer it from 90 degrees to 45 degrees. it must be even. find the center of your angled steel and the center of your

take you angled steel and evenly hammer it from 90 degrees to 45 degrees. it must be even. find the center of your angled steel and the center of your

  • 0
  • 0
take your lic plate and vanity trim if that's your preference, place them over your bracket with a marker, mark your holes. remove the plate. with a h

take your lic plate and vanity trim if that's your preference, place them over your bracket with a marker, mark your holes. remove the plate. with a h

  • 0
  • 0
from your excess steel plate cut 2 triangular braces and weld them in. now grind both sides smooth.

from your excess steel plate cut 2 triangular braces and weld them in. now grind both sides smooth.

  • 0
  • 0
on a flat surface weld both sides of all plates then grind them smooth.

on a flat surface weld both sides of all plates then grind them smooth.

  • 0
  • 0
cut the bottom of the bracket at a measure of 8". then cut the sides at 5" each.

cut the bottom of the bracket at a measure of 8". then cut the sides at 5" each.

  • 0
  • 0
once you have the distances marked, transfer them to the flat steel bar. the bar should measure approx. 13". the distances of the holes when placed on

once you have the distances marked, transfer them to the flat steel bar. the bar should measure approx. 13". the distances of the holes when placed on

  • 0
  • 0
this is the furthest hole. these two will be used to secure the bracket to the car.

this is the furthest hole. these two will be used to secure the bracket to the car.

  • 0
  • 0
under the front of the car dead center you will find this small 7mm screw. further back there is that hole and even further there is another hole exac

under the front of the car dead center you will find this small 7mm screw. further back there is that hole and even further there is another hole exac

  • 0
  • 0
these are the tool you will need. you will also need the following materials: 36"x1"x3x16" steel flat bar 2 ea. 5/16" x1" #18 hex bolt 2 ea. 3/8" l

these are the tool you will need. you will also need the following materials: 36"x1"x3x16" steel flat bar 2 ea. 5/16" x1" #18 hex bolt 2 ea. 3/8" l

  • 0
  • 0
the final product.

the final product.

  • 0
  • 0
20150203 210728

20150203 210728

  • 0
  • 0
20150203 210647

20150203 210647

  • 0
  • 0
20150203 205839

20150203 205839

  • 0
  • 0
20150203 205755

20150203 205755

  • 0
  • 0
20150203 205738

20150203 205738

  • 0
  • 0
574.jpg

574.jpg

  • 0
  • 0
573.jpg

573.jpg

  • 0
  • 0


Top