Alignment Specs - 20x11 +50 - 315/35/20 - 30mm drop

[Bigmac]

Alignment Specs - 20x11 +50 - 315/35/20 - 30mm drop

Posting up to see if anyone on here is running the same or similar fitment and what your alignment specs are.

20x11 +50 with 315/35/20 MPSS on a 30mm drop

At -1.9 left and -1.9 right camber, only the right is rubbing. Having a fresh alignment done tomorrow. Curious if anyone can advise what specs will be needed, within reason, to clear this. Thinking if I do -2.1 on right rear, I can get it to barely clear.

-James

Sponsored

 

[moarhorsepower]

Alignment Specs - 20x11 +50 - 315/35/20 - 30mm drop

Posting up to see if anyone on here is running the same or similar fitment and what your alignment specs are.

20x11 +50 with 315/35/20 MPSS on a 30mm drop

At -1.9 left and -1.9 right camber, only the right is rubbing. Having a fresh alignment done tomorrow. Curious if anyone can advise what specs will be needed, within reason, to clear this. Thinking if I do -2.1 on right rear, I can get it to barely clear.

-James

I'm running 305 in the rear. 19x11 +50mm offset. No rubbing, can't remember what the alignment specs are though.

Did you have the rear subframe centered? Using something like the CB005 kit from BMR? Maybe it's slightly shifted and that's why it's rubbing on one side?

 

[Bigmac]

I'll snag the Steeda subframe alignment kit now.

-James

 

[Steeda Tech JohnC]

I'll snag the Steeda subframe alignment kit now.

-James

just saw your order come across the screen as i read this lol

 

[Bigmac]

just saw your order come across the screen as i read this lol

:cheers:

 

[wildcatgoal]

Had similar issue with 315 tires when I briefly had some MMR wheels. Steeda alignment kit solved that entirely on my car. I can run -1.9 both sides, zero rub even on a road course. You will want to pay attention to your brake lines with that wide of wheel to make sure they are situated so that they do not rub on the tire like mine wanted to.

 

[Bigmac]

Had similar issue with 315 tires when I briefly had some MMR wheels. Steeda alignment kit solved that entirely on my car. I can run -1.9 both sides, zero rub even on a road course. You will want to pay attention to your brake lines with that wide of wheel to make sure they are situated so that they do not rub on the tire like mine wanted to.

Do you know what the width and offset was on the MMR wheels?

What was the full tire size? Curious how the height compares to my 315/35/20 if you were running something shorter.

-James

 

[wildcatgoal]

The wheels were 20x10.5. I don't remember the offset - I think 40? - but they were as far out as I'd ever go. The tires were Nitto Invo 315/35-20 tires. Driver's side rubbed.

 

[Bigmac]

The wheels were 20x10.5. I don't remember the offset - I think 40? - but they were as far out as I'd ever go. The tires were Nitto Invo 315/35-20 tires. Driver's side rubbed.

Cool. Thanks. If they were 10.5 +40, that means mine are 4mm less aggressive, so not much change. I think Nitto runs slightly narrow compared to the MPSS, so that probably makes up the difference. I'm going to install the Steeda subframe alignment kit and then have my alignment redone with a goal of -1.9 camber and see what happens.

-James

Sponsored