car still sitting on jacks, got a set of z26s for next to nothing. The rear brake pads are very uneven, the outers are all much more worn and uneven. The inners are all thicker but uneven as well. Not sure if the previous owner only changed the inners or what but waiting on amazon to drop off...
if i remember correctly it stops about half way down but im gonna throw the wheels on and go for a test drive. Right now when I press the pedal with the car running it hits about half way and then I have to press down harder to get all the way down.
Please mansplain away, I've never had to bleed breaks before ( obviously lol ) and the more I can learn the better.
I re bled all the brakes 3 more times. Starting with the passenger rear then driver rear then passenger front inside the outside then inside then did the driver inside, outside...
you wouldnt have a link to the correct fitting for the top?
Thanks Ill look at this as well, im assuming even with the car off I need to pump and hold or just pump?
Also while the brakes were being held, I did the passenger front and nothing came out, Now this is after I did the rears but I...
I'll give this a try, I've been doing the outside first then inside then moving to the next one .I thought you were supposed to work your way towards the master cylinder.
Thanks
Hey,
This is the second time I've tried to bleed these brakes (pp1 package ) and can't get them tight. I like my brakes on the touchy side,when I first got the car they were super tight. Currently I can press my foot to the floor.
How I'm currently/have done/doing it.
Start passage rear...
Hey,
Car is a 2018 gt with 42k cai and 93 tune, lowered on springs. Past few weeks when I'm backing into my garage I've been hearing a crunching/grinding noise when shift from drive to reverse. It doesn't make the noise when I first start it up and it doesn't make the noise when I go from drive...
5 star gave me a call today after I called them again on Monday. Honestly think they just forgot about me from last week but sh*t happens and they seem busy.
Anyways they said they think they issue is the intake. It's a jlt intake, they sent over a new revision and it's much better not 100%...
Thats the issue, I have a CAI. If I could find the right sensors I would just replace them. Looks like I have bank 2 sensor 1 ( upstream ) the other ones I got from rock auto wont work.
I filled up with 93 when there was 9 miles left in the tank and have driven 3/4 a tanks worth of gas since e85 was in there. I got the cel when e85 was in the tank and still had it after my second revision. I can drive the car for about 30+ miles and then it will come on, but you can tell the...
I've tried both my 89/93 perf tunes and they all have the same response. Currently on 93 perf. Very hesitate to move, turns over a few times before starting, loss of power etc etc.
Would 2 of these https://www.rockauto.com/en/moreinfo.php?pk=11967373&cc=3441002&pt=5132&jsn=1508
And 2 of these work? https://www.rockauto.com/en/moreinfo.php?pk=10180504&cc=3441002&pt=5132&jsn=1517
Maybe i'm over thinking this but half the sensors I look at show a different connector (...
After tuning with 5 star tuning and running there e85 tune my car ran like hell so flashed back and now im getting a p2097 and p2099. So i decide to switch out the 02 sensor. For upstream I order part # dy-1442 for down stream i order part dy-1291 from rock auto. Down stream is not even remotely...
" 'd have to disagree. I imagine your post of the events is to the best of your recollection. What state of mind were you in when you attempted to pass? Angry, bothered, scared, etc.? In a scenario like this, if they're already ahead of you, just slow down a couple MPH, create separation. You...
my whole point of this was the fact if you accelerate and turn the wheel less then 45 degrees you get a decent amount of oversteer. If I was going 60+ I could understand the comments but 35-45 is hardly a good reason for the car to react like that.