Perfect thank you, just read up on them, car is on jacks now and I will take a look into it, I am also reviewing the long driveshaft/vibration thread that is on here. I am on the manual as well and it does state it can be driveshaft or parts surrounding it causing this. Especially the clunk, I...
Does this cause vibration? Or is it just a clicking noise? I have a slight vibration that i am chasing down that has been on the car for a bit now that i want to fix considering that when i let off the throttle at 140+ i feel the car vibrate in half a second intervals
Okay cool it was 8QT they confirmed with me that since Gen2 pan then it is 8, not sure what they did to make it work but i trust them so I’ll go with that, thanks everyone
hmm, I didn't receive pictures. I actually have to reach out to them about those, they told me it was going to shipped with the Motor, but it was just my receipts and startup instructions. I sent them my pickup tube and the oil pan so I would have expected them to use that. It is a very...
I am on a Gen 2 Oil pan, I sent the one from my Gen 2 to the builder and they installed it, so now I am confused, Im pretty positive it is a Gen 3 because they stated that is what is going to be used, and the top of the short block looks exactly like the Gen 3 so not sure how they made the oil...
Dumb question, am on a Gen 2 car, it was previously a Gen2 short block and is now a Gen 3 short block with Gen 2 heads, anyone that is experienced that can Chime in and let me know if it is the 10qts, or the 8? I'm leaning towards 10 but not 100%, ill still be checking oil level with indicator...
Had an accident when removing my motor about 2 years ago , the Crankshaft Position Sensor wires ripped, I already fixed the green and yellow wire. There is a 3rd exposed wire which not sure where it leads. Anyone know how to go about that wire?
The picture shows the silver wire which is the...
I got a reply from RPG, they said Manley is more for Gen1 but can be made to work(doing gen 3 block/gen2 heads) RPG is working to get me some directly. Lets hope this project gets finished up before November
Any other valves available other than Ferrea For built motors? I am having a motor built by RPG and I want to get better valves than stock but I have ordered Ferrea from different sites twice now, one a couple months ago which advised me that they don't have them available and refunded me...
yeah i had an issue with the crank pulley torx screws they were so tight i was able to get only 2 out without breaking about 6 torx bits and then some of the rest came out witj heat and the last two stripped. I had to drill them out, the ATI pulley i got was a POS because a shop scammed me and...
so i have a Crank hub for an ATI that does not want to come out for anything. I have used a 3 jaw puller and a torch plus a combination of a sliding hammer with the 3 jaw puller. I honestly just want this thing out asap , i need the other components inside but any tips on removing this junk? i...
trust me , ive done some unusual things to get it to move and it didnt work lol im pretty sure i know the issue, just gotta get back to it, should be out by tonight once sun sets
so i got the motor out of the trans but the motor isnt coming out.. AZ heat is starting and i need this out. the passenger side continues to be an issue, i removed the druver side header. When i lift, the motor doesnt want to come out of the motor mount
Having issues removing engine.. i have removed basically everything including the top transmission bolts the 2 on driver side and 2 on passenger side.. i tried lifting it however only driver side seems to go up. Is there any other bolts i may be missing besides those that the transmission might...
So i went the RPG route, they advised me to get Ferrea Super Alloy 0.5mm oversized intake and exhaust valves with pac-1217x springs. I'll be doing ARP everything since their assembly includes it, which makes it easier. I'm excited and ready to party, was given end of december time frame.
okay, I see that you did your build with BES racing and thats who Im expecting to go with next weekend or so.
When you built yours, did you gather the parts beforehand or did you agree on all the parts with BES racing?