Search results

Looks great...! Did you use Ford touchup paint or something else to do it with? Same exact thing I was thinking about doing, which is also why I spent the extra $$$ to get this CAI. ;)

I bought the kit because of the "Ford Performance" Embossing on the front, which the GT350/Mach1 intakes do not have. It's also my money to "waste", but I got what I wanted... Also, I can say, install complete now, from what I've read here (and I've read the entirety of this post months ago in...

As I stated, I already have my tune file from them. So, yes, they do, and it didn't seem that they had any issue with it. I've been with Lund for a while now and they tuned my 2014 GT CobraJet setup with the tricky FTPP big monoblade TB and my car ran absolutely flawlessly. A little high on...

Just got my kit delivered today and have a Lund tune ready to go (Been with Lund for my past 3 Mustangs, hands down the best!)... Not even messing the ProCal. Will be installing tomorrow with an Airaid (860-399, oiled) red filter and ditching that paper filter. Also have the UPR full (drivers'...

I've seen that one pop up at AM, new player on the block.. Going to research the fueling on it. Still like the looks of the new V2 CJ better though with that bold FORD PERFORMANCE logo on the side of it. ;)

Hey all, Has anyone installed the new V2 CJ Manifold here and if so, how was the fitment with the stock hood (pics please)? In pictures I've seen it looks like it has a lower profile and the TB neck looks like it turns down a little bit more than the older original design. (Using Steedas...

Has anyone here just taken the intake parts, ditched the ProCal, and had it 3rd party tuned? Like with Lund or PBD? I currently run the Roush CAI, Corsa Long Tubes and H-H catback, Lund tuned and it runs like a banshee. But I love the Stock Mach 1/GT350 look of the FRPP CAI over the Roush's big...

How is street drivablilty with it.. ? I'm looking at this as well as the FP CJ CAI, but I'd have to get the JLT bucket for that too work with the snorkel. Unless maybe it would work with Steeda's MaxFlow bucket.. ;) Steeda - Could I buy just the MaxFlow bucket if I went that route. Or do you...

Will that 11-14 CJ CAI ( Intake https://performanceparts.ford.com/part/M-9603-M50CJ ) install/fit into an S550? Has anyone here tried it yet? Does anyone know if the dirty air inlet will mate up to the grille opening correctly? Would kinda suck if you can't get all the cold air into that box...

Posted in another thread but figured I'd post here as well. I've had this rattle/tapping sound develop right after I installed my Corsa catback actives, at the rear Passenger side. They sent me replacement valves which did not fix it. Even sent just another passenger side valve after that...

I've had this rattle/tapping sound develop right after I installed my Corsa catback actives, at the rear Passenger side. They sent me replacement valves which did not fix it. Even sent just another passenger side valve after that, which still did not fix it. Mine sounded like a tin can tapping...

Hey there! So a little overwhelmed with the 225 pages so I'll just ask: I would love to change the default 3 signal "Flash to Pass" to 4 signals. I think I have already got that one down from what I've read (unless the SCCM as-built for that has changed for the 2020 GT's). But I would also...

I've been meaning to report here that I used Pennzoil 5w30 in my last oil change a couple of weeks ago. I could always hear the rattling at 1900 - 2200 RPM at a sub-moderate level. On warm up the most until it's hot and then you can barely hear it. With the 5w30 in I have observed a noticeable...

Mine cold is more like your second video and warmed up like your third (I can still hear it, but barely)… Actually the loudest I hear it is not when I am driving and rowing gears, but standing in the driveway and revving (and holding) at 2K-2300. I guess I have one of the quieter instances of...

Hey all... I just registered here after reading ALL 72 pages of this thread over three days... Add me in to the 2K - 2300 RPM rattle... I started noticing mine after my first 6500RPM 1st gear pull at 800 miles on the ODO. ...I special ordered mine back in March (17th) and it went into...