Search results

It is a two step process, first connect phone to radio via Bluetooth then you do the same to Motorola device. Once the radio sees the connection via Motorola for the first time it will prompt you to allow for Android Auto. Do so and then your pretty much done. I will say, it takes about a...

Cyanlabs only works via USB and must be MY 2019 and older APIM. Also, to do a Sync and Map update the program with downgrade to older Sync version, format the system, clean installs with new version along with maps. Also, make sure to do a master reset after it comes up for the first time when...

Cyanlabs Sync Updater... Read and follow directions closely!!! https://cyanlabs.net/applications/syn3updater/ Software and maps!! All I use... Current versions for both on mine are: Sync: 3.4.23188 Maps: 2.24 (2024) NA (North America)

Have three of these in separate cars and have no issues with it... Do a search in the forum and get some further info...

So got to ask, after you replaced the battery did you also reset the Battery Management System (BMS). If not, it's recommended... BMS reset - no tools required | 2015+ S550 Mustang Forum (GT, EcoBoost, GT350, GT500, Bullitt, Mach 1) - Mustang6G.com

Followed the same on my 15, cut zip lines in trunk to eliminate the stress on the wires and then bought the replacement camera that was listed in the recall for my vehicle. Place new one in and the used Forscan to calibrate camera as stated above and my backup lines were correct. Did not want...

General settings, factory reset... Should always be done after updates and you stated it took one correct? Anytime I run the update via Cyan Labs as soon as it comes back up I do a master reset and move on from there... Knock on wood 🪵, no issues as of yet!!!

You are correct, I meant to say Bullet not sure why I wrote Mach I, long week... Ha ha

Pretty sure it is hard coded in the firmware bin file of speedo. I know they have a separate file for Mach 1 assume it is the same for the GT500... may want to reach out to breeves directly....

Agree, must be careful... hence the read is important!!!

https://cyanlabs.net/applications/syn3updater/ Read up, but this where a lot of folks get there updates... Been using for years with no issues!!! Once download on Windows machine pretty easy to use... GL

Also a big MA1 fan!!! Have you seen these, little pricey but may fit the bill... Not sure how well they work but may be worth it? https://www.amazon.com/Wireless-Charger-Mustang-2015-2022-Charging/dp/B0CXPVRRLN?gQT=2

Have the MagnaFlow street on mine since 2016... Fits perfect with no rubbing issues and feel the sound is good. Started with a MBRP exhaust and had so many issues with fitment that they ended up refunding the full amount and I turned around and bought the MFlow exhaust systems.

Moving to DM.. Check...

Well that's good news... Which line and code did you change to cause this? I'll check mine... Remember his code is only a starting point.

The speedo came from a manual car... If so, the speedo needs flashed internally to be automatic... Will need to be sent out to be flashed with special software and file... Reach out to Breeves, he flashes for a fee... Pretty sure that is your only option unless someone else chimes in with...

Go 20 x 10 on all four this way you can rotate front to back... My current setup on mine...

I have a 2015 with Dash conversion... Mine are as follows for those two lines... My high beams work normally, push forward for on, pull for flash to pass... 724-01-01: 0020 2628 724-04-01: 4840 0000 Hope they help... GL

Found this so maybe it can be changed... I was told differently a few years back... https://www.ford-trucks.com/forums/1749301-2023-super-duty-kph-to-mph-3.html

You 100% sure? I had to have mine flashed to fix from auto to manual. Was also told that needed to be done from going to mph from kph also. That is also how they apply the bullet Speedo info to the dash using another BIN file.