Search results

******************************************************************************************* Larger dial for resolution and readability 3-4" 0-60 puts 30ish pounds in the center of the range, which is the most accurate area. so a 3.5" 0-60 industrial grade (non-chinesium) gauge adapted to an...

20k in 2 yrs sounds normal for someone who drives it every day, esp. if its a long commute. If I had one it wouldnt be a garage queen.

https://www.amazon.ca/Joes-Racing-32307-Pressure-Gauge/dp/B00404WDUC/ref=sr_1_2?crid=Y2CRUD2A7OST&keywords=joes+racing+air+gauge&qid=1655388543&sprefix=joes+racin%2Caps%2C126&sr=8-2

v6 base had excellent brakes Gt PP brakes rock at highway speeds, but about town are no better than the v6's ... ie great, but not more bite, and you'd never know they were diferent tried going the cheap route before with jobber rotors and pads. sucked majorly and had to go OEM to get good...

also possible loose intake pipe at throttle body. happened to me, loose band clamp. thats easy to check, then what he said - lol.

sounds like the battery is possibkle degraded 2nd battery in trunk closer to the amp. with ACR (automatic charge relay) isolates the 2 until alternator making enough jiuce to charge 2nd battery. (ACR under hood to save cable) suitable large wire gauge to trunk for load,

Was in same place this weekend. Used spray paint can. - Duplicolor shade Red is the hardest color to cover with. Heavy coat caused bubbles .. so while wet, wiped it off. Light sand and (grey primer this time) it covered much better. Also sprayed down and wiped with brake cleaner before priming...

have a conducance type tester. been getting same messages every other day. checked today - 100%health, 32% charge - weird as voltmeter indicates its always charging in use. 14.6-.7 in use. 12.3 in am before starting No issues starting or using it. On charger with a restore cycle right now. see...

had the same experience on my oil change. ran the engine and left it for a while, no change. added half a qt. Oil change places in my experience will do a top off if low. I was lucky I had some of same oil kicking around from prev. car.

uhoh ... did the same a while back dealer wanted $15 (cdn) for just the clip. Tried Dorman assortment pak ($3) as well - same experience - dont fit,

test drove an ecoboost and gt back to back. was unable to order an ecoboost for 6 months dealer says .. so got a year old gt off the lot. the eco tester I drove was already sold. The ecoboost is a bit more fun in that you can stomp the pedal. Gt you have to pick the conditions and how much...

you betcha. Canadaseatskins web site, but box and tags are Kats'

nice treatment on the mirror stalks ... and a great shade

So this is for cloth interior folks .... leather folks wouldnt appreciate it not "having come from cloth" First grocery run in the new Katskins - getting out, one's butt spins soooo easy!! Then noticed getting in you slip smoothly into position. I hear ya smirkin' lol. but it's really such a...

seat heater before gluing. color is still too red in the iphone, but close-ish a lot of fighting with the clips and stretching covers off/on. not complicated - no instructions though. dunno if i mentioned it last post -- install the seatbelt strap magnets first. they actually provide witness...

So color - cardinal red .... looks just like the demo shot on canadaseatskins. However iphone is really accentuating the red, and its way more subdued than photos indicate. However, so far im over the moon with the change. back seats done first last evening ... very straightforward. front...

A/C leak can occur even if not used. Most common is the seal at the pulley end. There's a bit of oil circulating with the refrigerant, and when the seal leaks you get a telltale stripe of flung oil on the underside of the hood - side to side above the pulley. Some will blow back on the block...

well my weekend's booked now

Pollen season winding down, was more than a wash job .... clay bar worked wonders getting paint smooth again. New Makita cordless polisher was awesome. Going from a porter cable (which is really great) I was surprised what I was missing. Makita is beautifully balanced, and a one handed machine...

Bilsteins .... dew eeet! Ended the wiggle in the rear end on cornering on my V6. Ride was only better, with a very nice compression stroke and effective rebound damping. Fancier setups may be better, but for the price, the ride only improved ... no harshness Also if you have 20" rims...