Search results

Installed MMD Rocker Panel Winglets today. I had them home for maybe 6 months but I was too lazy to install them :cwl: Still I doubt that they are made by MMD and I think that the seller sold me some cheap Chinese copy. They came with no installation material, no instruction booklet, no box...

No. Just no. I don't even know which side I should start from 😂 The hood - air goes in, but doesn't go out. It gets trapped in the engine bay area. Front bumper is Galpin wannabe but it looks terrible on the sides. Rocker panel winglet directs the airflow into rear tire, not around it, because...

As long as FORD WSS-M2C961-A1 is basically ILSAC GF-6, I think you can safely use Amsoil Signature Series 5W-30 which exceeds all the known factory requirements. It is not cheap, but If you are looking for the best Full Synthetic engine oil on the market like I do, AMSOIL Signature Series 5W-30...

Hello. Is it possible to obtain a window sticker from that system also for EU spec Mustang please? My VIN is 1FA6P8TH1K5141094. Previous owner wasn't car guy obviously and didn't keep it :D I wonder what was the original setup like. Thank you :)

Because I am from Slovakia, bought the car in Slovakia and drive it here, however the government wanted me to pay 2800 EUR for the registration 😂 So I opted for temporary residency in CZ and paid 1000 CZK for "evidenční kontrola" and 800 CZK for "registrace" which is like 120 EUR together 😂 U...

I've been designing custom hood stripe over the last month. I based the design on the original Mach 1 and made a few tweaks to it so it matches my color and wheels. Most of the time I spent taking the measurements over and over again and redesigned the stripe maybe 15 times until it was lining...

Did you try hot water or toluene?

200 USD for that job not only sounds reasonable, but I think it is really good price. If you don't have the right tools, you would have to buy them and it's like at least half of that price. If you buy a rotary polisher not a DA polisher, it will cost you 50-60 USD. Then you need 5000 and 7000...

If you open it up on a highway all the Porsche/Pagani/Ferrari guys will be sooooooo envy. Got spoiler? Beat this :cwl:

Correct. You really don't have to paint all the layers in a single day (I know it is tempting :D ). As the paint is drying it is shrinking its volume. You don't want the paint to form any bubbles or cracks just because you put there too much paint. Give it good 2 days before adding another layer...

Looks good. I think you will have to add some more paint in the next few days :) Those dents are pretty deep and you can see on the left side that there is more paint needed to level up the surface. If you don't level up that dent with paint to the surface level, and just add clear coat, you...

You're welcome :) I was scared too and I also wouldn't wet sand clear coat without any knowledge. I spent good two weeks researching how to do it properly and also called some local paint shops to get some advices on how to do it and what to avoid. But to tell the truth, I never done this before...

With a paint pen you can remove it completely not just make it "not to be too noticable". The only difference between the results is how much work and time do you want to put in. I ordered paint pen directly from my local Ford dealer. First step is to clean the surface and let it dry. Then you...

They had an amazing Malbec (for tasting) and Merlot (for cooking :cwl: ). I took also some Moscato bottles for ladies. Being a man I do personally prefer red wines. These were local and were really good, but based on a personal preference, I prefer Tuscan wines especially those from Castello...

I took her for a spin to get some wine from a local winery. Their gate and entrance looks so amazing that I couldn't help myself and take some photos. Phone: Samsung Galaxy S20 (shot in pro mode)

I am currently putting hood stripe on my Mustang. The only difference is, that it is custom design based on Mach 1 stripe with few tweeks, so it would be pretty complicated and expensive to get it painted. But if I had to choose simple racing stripe, I would paint it without thinking any...

It didn't cross my mind, but that's really good idea. Thank you. Now I have to do the same :cwl:

Finally found some time to clean up that mess under the hood extractors.

Thank you so much for your help 🙏

Hello everyone. I am currently trying to design hood stripe for my 2019 Mustang based on the shape of Mach 1 stripe. I really like how this stripe is in line with the line that goes from the heat extractors and over the roof. I almost got it, but I can't figure out the width of the stripe at the...