Sponsored

Recent content by wagnor

  1. boardkat's Daily Driven CAM-C AutoX Slayer!

    Why am I competing in CAM again??? My god man! Is there another level above CAM for you??? LOL all JKs. Hope you can put Team GM in their place this year. I might have to stop and de-mod the stang to compete in more of a street class. Spent an hour reading all this. Mind blown!!!!

  2. DIY 18' manifold swap into 15-17'

    Thought everything was working good but then I got a CEL p2006 valve is now stuck closed. The first couple of revs I can see the voltage showing the valves opening and closing. When I did a datalog to higher rpms the voltage stayed at the closed indication and never opened up again. I’m stuck on...

  3. DIY 18' manifold swap into 15-17'

    I sent you a Pm on messenger

  4. DIY 18' manifold swap into 15-17'

    So confused. Vacuum 1 connects to what? Vacuum 2 connects to what?

  5. [?] '18 Intake Manifold on '15-'17

    Just found the DIY section. Thanks for the info. Going to review that.

  6. [?] '18 Intake Manifold on '15-'17

    Valves stuck open on mine too. What did you do to fix this? How did you route vacuum lines?

  7. [?] '18 Intake Manifold on '15-'17

    Ok have pigtails installed. Have the blue plugs spliced together. Now I can’t get rid of the p2005 code. Says the valves stuck open. Voltage shows them open at 3.4 volts. Desired is showing either 0 or 1 which should be the voltage to close. Is this a vacuum issue now? Anybody have a schematic...

  8. [?] '18 Intake Manifold on '15-'17

    Irmc staying open even after commanded shut. Maybe I have the vacuum lines on wrong in back. Anyone have a visual on correct route of vacuum lines?

  9. [?] '18 Intake Manifold on '15-'17

    So what controls the opening and closing. The blue plugs or grey plugs? I guess I’ll have to get the multimeter out and check for voltage. Idle and reviving the voltage never changed from 3.3-3.4.

  10. [?] '18 Intake Manifold on '15-'17

    So I spliced the two blue connectors and swapped the longer 3 wire connectors from side to side. From looking at the data log in idle to 3500rpm rev the signal from the IMRC was between 3.3-3.4, I believe this is the voltage required on the 18 IM for being open. Question is when do they close...

  11. [?] '18 Intake Manifold on '15-'17

    Great explanation!!!!

  12. [?] '18 Intake Manifold on '15-'17

    Leaving one of those blue plugs disconnected with throw CEL either p2008 or p2011. Don’t believe this is tuned out.

  13. [?] '18 Intake Manifold on '15-'17

    Currently running the PnP harness and I’m throwing DTCs p2004 and p2008 tune confirmed the correct voltage is set. I have one blue plug connect and the other disconnected. Anything else I should check? Currently waiting on datalog review for any corrections needed.

  14. How to reduce IAT's, improve flow & positive pressure with PMAS & other open CAI's

    Yes it don't fit. As of right now I've used heat tape to keep them together. Need to find a big enough hose/tubing to connect the two with some sort of clamps or could also do the drilling and zip ties method. It's a weird irregular shape so it's going to be rough trying to get a perfect seal...

  15. [?] '18 Intake Manifold on '15-'17

    Ordered and shipping info. My pigtails just shipped today. Ordered on 2/21. Intake ordered on 2/5. Delivery scheduled today.
See more


Top