Post Your Mach 1 Pictures

[Tshenberg]

Added a few overlays to make just a bit more unique

Sponsored

 

[stangcrazy]

Added a few overlays to make just a bit more unique

Really like the accents in the engine bay. Im old so i would call those valve covers but IK they are not lol. did you paint or an adhesive?

 

[Tshenberg]

Really like the accents in the engine bay. Im old so i would call those valve covers but IK they are not lol. did you paint or an adhesive?

Thanks ! They are vinyl overlays. A company called Bemaro makes them. Bemarofilms.com they are specifically precut for Mach 1

 

[Atlas1]

Thanks ! They are vinyl overlays. A company called Bemaro makes them. Bemarofilms.com they are specifically precut for Mach 1

How was the install? I’ve got the emblem overlays I need to put on. Looks kind of tricky as they have to be stretched, then heated to get good coverage.

 

[Tshenberg]

How was the install? I’ve got the emblem overlays I need to put on. Looks kind of tricky as they have to be stretched, then heated to get good coverage.

They are a little fiddly to line up. But I didn’t need to heat up or anything. Just cleaned surfaces with denatured alcohol first and used soapy water to line up
Send pics once you’re done ? I bought those too but haven’t decided if going to add

 

[Atlas1]

They are a little fiddly to line up. But I didn’t need to heat up or anything. Just cleaned surfaces with denatured alcohol first and used soapy water to line up
Send pics once you’re done ? I bought those too but haven’t decided if going to add

Will do. I really want them on but I haven’t had time to mess with them. The instructions indicate that the overlay is made slightly undersized so that it can be stretched. Once you have 1 side where you want, you stretch it and press down to get full coverage of the emblem. Remove transfer tape and then use heat with pressure to seal it on. Seems easy enough my only concern is how small the pieces are. I need smaller hands lol

 

[Mach1BC]

 

[PICASSO]

John, I think they look amazing. Do you have 19-inch or 20-inch rims? I'm wondering if smaller letters will hold up more as they would be less likely to buckle when the tire sidewall comes under pressure. I would love to get them in blue to match my Grabber Blue car. Looks like you cannot power wash them clean.

I have 19" rims. I ordered 1.5" letters. If I was to do it again, I would probably go with 1". I will never have to power wash my wheels. My car never goes out in the bad weather. Grabber Blue would look so sweet on the Grabber Blue Car.

 

[Pipefittermax]

The letters can be a little fussy to line up. I like the color burst it adds to the vehicle. I used the same installation process, swab with alcohol and soapy water for alignment.

 

[Banjoeyes76]

nice. Used or new M1 with HP?

Used, barely…976 miles w/ HP

 

[Atlas1]

The letters can be a little fussy to line up. I like the color burst it adds to the vehicle. I used the same installation process, swab with alcohol and soapy water for alignment.

Love it. Any chance you could expand on the emblem overlays? Tips, things to avoid, etc
You may give me the inspiration to tackle this sooner

 

[traxiii]

The letters can be a little fussy to line up. I like the color burst it adds to the vehicle. I used the same installation process, swab with alcohol and soapy water for alignment.

where'd you get all that yeller stuff??3

 

[dpAtlanta]

damn the 350 is a great looking stang.

Yeah… but the Mach1 is the new Shelby GT350 replacement…. Let it roll.

 

[Pipefittermax]

where'd you get all that yeller stuff??3

https://www.bemarofilms.com/onlinestore

 

[Pipefittermax]

Love it. Any chance you could expand on the emblem overlays? Tips, things to avoid, etc
You may give me the inspiration to tackle this sooner

Be patient when putting these on. I would not use a lot of soapy water. I struggled putting the Mach 1 on the rear deck lid. I wish Bemaro would put out an installation video on YouTube.

Sponsored