Taillights with Sequential Amber and 3-bars Brake MOD!

[papinist]

Very nice!!
Is this the vinyl kit from Dennis?

Where have you placed the stock mode switch? I see that you change it on the fly! I have the switch in the trunk, in the spare wheel pit, so I need to reach it to switch to\from stock mode. But I plan to use it very rarely so it's not a problem

Edit: nevermind, I just read that you bought US taillights - this explain why they are so beautiful.. a perfect US red!!

Sponsored

 

[Ian whu]

They red USA lights.
Switch is in boot. Can't change it on the fly unless someone in boot (trunk) )

 

[papinist]

so why in your video you have sequential and stock mode at the same time?

 

[Ian whu]

so why in your video you have sequential and stock mode at the same time?

I cut the wire on one side, and not on other side

 

[yellowpony]

Hi Papinist,


Thanks for great write up mate, Could you please show us the photo of reverse light globe. Are there two separate globes or only one in the housing. it would be much appreciated if you could please.

Cheers

 

[papinist]

Hello Shane,
I don't have that picture ATM but for sure there are two bulbs for reverse, one per side, and another bulb for fog light. Can't remember in which thread but our romanian friend Lsstefan posted some pictures..

 

[John577]

Hi Papinist,


Thanks for great write up mate, Could you please show us the photo of reverse light globe. Are there two separate globes or only one in the housing. it would be much appreciated if you could please.

Cheers

Hi Shane,

Here's my post about the reverse bulb.

http://www.mustang6g.com/forums/showpost.php?p=916000&postcount=338

Cheers

 

[papinist]

I thought a lot about getting US red taillights or vinyl wrap my EU clear taillights. At last I decided over keeping my clear with red vinyl so I can always revert to stock

 

[Ericc B]

I now have Caniggia modified US taillights too

You can read about my adventures with them in my project topic:

http://www.mustang6g.com/forums/showthread.php?p=1144808#post1144808

Btw a little additional installation tip for the external sequential electronics modules that need to be tucked behind the bumper cover:

In both the left and right locations there is a bolt for the bumper frame right underneath the lamp location. By untightening this bolt you can actually stick the fork that’s on the module’s casing underneath. Then bolt it back up and the module is locked in place like a rock.

 

[papinist]

Guys, caniggia has its account temporarily locked since it's not an official vendor here, but he can answer to PM .

 

[YLA G]

Nooooo

 

[Ericc B]

Wtf :doh:

 

[Ericc B]

I made a video of my finished US taillights. Park and brake lights in triple red, blinking in sequential amber.

 

[mimi6060]

Hello Ericc-B

Your modifications on on your vehicle about your rear lights . Is that these are EU lights with modified or altered US fires? What did you do about these changes? This is just plug and play because i -have ecoboost 2016 mustang but Europe version with crystal lights. Can you tell me the changes if it is easy to do and if it is plug and play ?
thank you very much
Have a good day

 

[Ericc B]

Hello Ericc-B

Your modifications on on your vehicle about your rear lights . Is that these are EU lights with modified or altered US fires? What did you do about these changes? This is just plug and play because i -have ecoboost 2016 mustang but Europe version with crystal lights. Can you tell me the changes if it is easy to do and if it is plug and play ?
thank you very much
Have a good day

Hi Mimi,

My car is an EU EcoBoost too. I replaced my crystal light units with a set of original red US lights that were modified by Caniggia of www.hd-customs.pl

You can read more about this mod on page 4 of my project topic:

http://www.mustang6g.com/forums/showthread.php?t=40642

The installation is not really plug and play, actually if you read this current topic from the beginning you will find a lot of info on what needs to be done to install them.

Sponsored