Too tight for me to get under that. Dropped it at my mechanic he said he put a 10 mm in and it still had slop thinking it might be a 12 mm allen wrench for the fill plug.? , I know the drain is an 8 millimeter
Anyone know a source for the retaining bolt on the stock front bermbos on a 16 GT? I think it s called the pinch bolt. It just spins when trying to remove and even vice grips won't stop it. Thinking I will have to sawzall the old bolt out. Tryng to find a source other than stealership, but AM...
I was looking at same exhaust. Based on your post I have eliminated the Mach Thunder.
Are you running resonator or no? Pretty sure the db level can be adjusted by moving the j pipes (if you installed them).
I installed the CB005 yesterday. I saw a few different methods of installation (loosen all 4 cradle bolts) , work side to side and pry cradle back into position, or do front only and then rear.
I didn't want to have to deal with realigning the cradle so I worked one side at a time, while...
One day event at CLT in two weeks 4/13
April 1 is last day for discounted reg $250
https://www.mustangownersmuseum.com/open-track-event.html#id=104&wid=201&cid=1250
Have run a dozen or so track events with my 16 with FRPP, about 12K miles 2 or 3 days usually about an ounce in separator I use a plastic syringe with a vacuum hose to empty so i don't have to take it apart.
Heavier weight means more friction, also less viscious, so less flow @ startup, and less trips through the oil cooler and filter.
While I have seen others complain of higher temps using heavier racing oil, I can only say running 5W 20 where the ambient temperature was 90 to 100 degrees, my...
I haven't had this issue at other tracks, just Dawsonville. The big carousel going into the front straight is a left hand turn. so you are being pulled from the thighs up into the pasenger seat. Always felt like I could take it faster but was always unbalanced.
Right hand turn no big deal you...
Dude thanks for posting that. I have been looking for an altenative to racing seats.
Does it hold you in for the lateral g's? When I was in Dawsonville I knew I could take that carosuel faster, but the lateral g's had me hanging on the wheel so bad my arms hurt.
How tall are you? I am 6'2 and with a helmet on I have to work to get my seat in a position where I can sit up straight and keep my neck straight. If you tend to lean forward when you drive or put most of your weight on your dominant side, it can cause bcak pain.
Mobil 1 5W20. Have had multiple track days where ambient temp was over 90. Never went over 55% on the factory temp indicator and never used more than a couple of ounces of oil over 2-3 days of 4K+ RPM. That is with the factory PP oil cooler.
Back in the day oil broke down @ high temps which...
Track Tape, Temp Wrap, clear vinyl or bra.
Tired of the tape and wrap. I don't mind taping the lights and mirrors but the front end s a PITA.
Thinking about a bra just for the track. Looked at the Novistrch but concerned about high IATS others have posted.
Maybe Covercraft?
What are...
2 quarts in 2K miles sounds more like a Vodoo, than a Coyote. I spend 2-3 days on the track at a time, hours of nothing but 4K RPM to redline and I only have to add a couple of ounces to top it off. I've never had to add more than that.
I would take it to the dealer, and keep your receipts.
PP 1,2, or 3 will keep your 3/36 warranty. Any other parts or tune and your rolling the dice with Ford, if you have an engine or power train issue. PP2 for about $800 installed you can't beat it.