Search results

I need to figure out why my active exhaust is not work working. Can I remove the lower valence without removing the rear bumper? I reallllllly do not want to have to remove the bumper to get access.

The shifter in my car feels a little too stiff. The transmission was replaced so I'm going to assume some level of incompetence is to blame. Aside from being maybe 30 percent too stiff it works fine. I would say the stiffness started after the engine was changed. I replaced the fluid but no...

Does any one have experience with Archetype Racing Splitter? They had one for the stock GT350 splitter but I no longer see it. My Type R splitter is looking worse for where and track season is about to start.

My GT350 is approaching 4 years old and 35000 miles. Probably 30 track days in there and lots of NYC roads (potholes). In addition to this the car is lowered on Ford Performance springs. When I drive now I am getting lots of bangs. And at low speeds my steering groans like an old person...

Get your minds out of the gutter!:cwl::cwl: Do the sway bar mounts or anything else require periodic lubrication? I am getting some groans when I turn the wheel I am trying to figure out.

My power steering creaks and groans when turned at low speed is there something that needs lubrication? Also my passenger rear suspension makes noise over potholes. My engine was replaced so the steering might be related to that. Also does anyone have an exploded diagram with the TQ specs for...

I was watching a video about the things cars do to make manuals easier. One thing they mentioned was cars will raise the rpms to make pulling of easier on a manual car. I knew the mustang did this but I have discovered I can give the car NO gas and take of just fine in traffic (Lazy I know)...

I have my motor replaced (2016) with a new R motor. I have noticed the new engine sounds different it also seems quieter.. I am wondering if I should be concerned. My dealer is fairly incompetent so I am wondering what mistake they did would cause this.

Good compare and contrast to the GT350

The screws that holds the front splitter on closest to each wheel is constantly being worn flat on my car what are people doing about this? Just keep replacing it? Id like a better solution

What track pads are you guys running and do you recommend them? I run Ferodo DSUNOs. I get about 10/15 days on them. I am on my second second but set at 500 a pop I am looking for a cheaper option. Initial bite is cold is good and I have used then on the street with out issue. I do not...

Has any one had their front bearing go? I have a speed related noise from my drivers side front wheel. Braking does not stop the noise but it does stop if I turn in one direction. My past experience implies this is likely a wheel bearing.

I am normally a JDM guy so I have had lots of toyotas/hondas/lexus's. I have recently started to buy american cars (chevy Trail Blazer SS, and now this mustang) I am some what ..concerned about the number of issues I have had thus far. I have had the AC fixed 2/3 times. The airbag in my seat...

I have for the last 2 track days been getting smoking from some fluid burning of on the exhaust on the drive side. I see fluid on the steering knuckle and under the brake fluid reservoir. I see also fluid on the belly pan and on the finder liner of the drive side wheel. The car does not leak...

Which is the best GT350R Replica Wing still available. The only ones I can find are the Anderson Composite and random Ebay $100 ones. Edit It should read GT350R I can not change it for some reason

Is there some kind of plastic repair epoxy we can use to fill in gouges in the splitter? Also does anyone know were we can get the rivets? I want to replace some of the ones that have been scrapped flat.

Has anyone replaced their clutch on GT350? If so what mileage? Any track days? I think either my clutch or slave/master or bearing is gone.

Pretty good price (1099) https://www.costco.com/QuickJack-5%2c000-LB-Capacity-Portable-Car-Lift.product.100460313.html

How did you tell how much life is left on the sc2. I have a track weekend coming up and I don't and to run out of tired in the middle. Is once the outside tread gone it done?

I have noticed a clicking when ever I hit the brakes now. It sounds like the pads making contact with the rotor. I have tried down shifting to simulate the weight shift during braking but I do not get the click. Also if I immediately press the brakes again I do not get the click. Has anyone...