What did you do to your UK S550 Mustang Today

[Hammer Time]

Not what I did but see this soap ’actor’ in a different light
https://www.thesun.co.uk/tvandshowb...ack-p-shepherds-mustang-clamped-outside-home/

Sponsored

 

[GR11M]

Not what I did but see this soap ’actor’ in a different light
https://www.thesun.co.uk/tvandshowb...ack-p-shepherds-mustang-clamped-outside-home/

That'll teach him to lower his car

 

[V8_MOTOR]

Just been doing bits and Bob here and there. Been meaning to get a good machine polishing setup and finally an opportunity came so I capitalised on that.

Also got a great deal on a 3inch cat back exhaust which I'm also reconditioning before I put it on the car.

And finally, I tried my hands ats wrapping and things went well.

 

[GR11M]

Ejector seat works

 

[WD Pro]

@GR11M

Now that you have done that, please could you give me a really good description of how to remove the little piece that’s sticking out funny on the left of the picture :

Without damaging it in anyway ?

Cheers,

WD

 

[WD Pro]

WD can i please see a picture of your garage with your mustang in it?
with this OCD you have going on i expect this car to be kept in a pristine condition heated garage.
many thank kid

No

But I do have two oils rads and a dehumidifier in there that waters the garden ... I assume you are OK with that ?

WD

 

[hinch]

Just been doing bits and Bob here and there. Been meaning to get a good machine polishing setup and finally an opportunity came so I capitalised on that.

Also got a great deal on a 3inch cat back exhaust which I'm also reconditioning before I put it on the car.

And finally, I tried my hands ats wrapping and things went well.

if you're bored and want to test that machine polishing stuff out I have a whole boat that needs doing that I can't be arsed to do

 

[V8_MOTOR]

if you're bored and want to test that machine polishing stuff out I have a whole boat that needs doing that I can't be arsed to do

LOL got plenty to be doing at the moment. Got a driveway full of cars that need TLC!

 

[GR11M]

@GR11M

Now that you have done that, please could you give me a really good description of how to remove the little piece that’s sticking out funny on the left of the picture :

Without damaging it in anyway ?

Cheers,

WD

Which bit are you referring to ?

 

[WD Pro]

Which bit are you referring to ?

That funny little plastic four sided piece that sits above the knee bolster / pad. You can see the recess for it to fit on your picture. I would be interested to see the back of that piece and how it mounts (mine is a little loose)

Cheers,

WD

 

[GR11M]

I'll have to check tomorrow, likely held in with those blue dash clips

 

[Kristian87]

Renewed insurance again with Admiral, won't go in to specifics but I paid £25 less than the previous year so pretty pleased

 

[raptor17GT]

Renewed insurance again with Admiral, won't go in to specifics but I paid £25 less than the previous year so pretty pleased

i got my renewal through start of week and yep gone down too

 

[V8_MOTOR]

I have been busy doing a light enhancement on the mustang. 80% correction with rupes fine pad and menzerna step 3 super finish polish.

Tje first picture is a photo where it has had a sealant and a single coat of adams polishes ceramic paste wax.

Also put on the solo performance mach xv 3inch cat back and am very happy with it. Sounds amazing.

Having the lift has been a god send. I haven't had to break my back at all with the machine polishing and waxing etc and the ability to just get it up and swap the exhaust out like it's no big deal has been amazing.

I think it's fair to say that the lift has already paid itself off.

 

[maddog1982]

Ordered these from the USA - Hopefully no more crap lights once I get some decent D3s bulbs too:

OEM 10-19 Ford Mustang 35w Xenon Ballast HID Bulb Control Unit Light Module and cables

Sponsored