What did you do to your S550 Mustang today?!

[WildHorse]

Looks great, GB unite.

ohio got rid front plates this year, very happy with that, your car looks great.

Thanks, here the law states
" Manitoba law requires that a licence plate be affixed to both the front and rear of the vehicle. (Exceptions are repairers, dealers, motorcycles, mopeds, tractors and trailers. These types of vehicles have one plate, which must be affixed to the rear of the vehicle.) "
Makes no mention of where on the front or rear of the car you can mount the plate. Almost 4 years now, never got hassled for the front tucked inside the lower grill.

Sponsored

 

[FreePenguin]

I did that before the law went in effect, I put a rectangle of PPF on the front bumper, then put double sided 3m sticky tape all around the edge of license plate back. then I stuck it to the PPF, I removed the PPF and the license plate came off with it lol

 

[Chef jpd]

Was disgusted by the engine cover atrocity on my 2020.

So, ordered the Bullitt "fuel rail covers", then did a big trim of the factory cover only retaining the center section.

Also did a sound tube delete while I was there.

Thoughts?

20201021_144836 by chefjpd, on Flickr

20201021_153408 by chefjpd, on Flickr

20201021_153423 by chefjpd, on Flickr

And, while I was there, I plasti dipped the tops of the headlights. No reason to light up under the hood.

20201021_153432 by chefjpd, on Flickr

 

[Solteka]

After uploading a revised tune from PD Tuning on my car earlier today, I did datalogging hours later with my COBB AccessPort and sent them the logs to analyze.

The car pulls really well in the upper rpm ranges now and drives butter smooth, now the car gives out a peak boost of 23.XX PSI before settling down to around 21.XX PSI during WOT.


After all that was done I gave the car a good wash on the exterior, wiped and vacuumed the interior:

 

[ice445]

Was disgusted by the engine cover atrocity on my 2020.

So, ordered the Bullitt "fuel rail covers", then did a big trim of the factory cover only retaining the center section.

Also did a sound tube delete while I was there.

Thoughts?

20201021_144836 by chefjpd, on Flickr

20201021_153408 by chefjpd, on Flickr

20201021_153423 by chefjpd, on Flickr

And, while I was there, I plasti dipped the tops of the headlights. No reason to light up under the hood.

20201021_153432 by chefjpd, on Flickr

How much are the Bullitt fuel rail covers?

 

[2morrow]

@Chef jpd I dig the look. It would be really cool with your lime green color on the cover(instead of blue) and have either lime green accents like text on the rail covers or have the body of the rail cover in Lime Green with black text/logo.

Just a thought...

 

[Decanes]

we Mustang on a 2nd amendment shopping spree today

 

[Decanes]

Stopped and got some good food at Bombshell and Ales

 

[Interceptor]

we Mustang on a 2nd amendment shopping spree today

How's your ammo supply, notice extra mags were empty. Getting tough in my area

 

[frank s]

Spent a few minutes irritating the Gray Car with pieces of my supply of Orange Reflective Vinyl Tape. Thinking about striping it one way or another. Possibilities are unlimited.

I had some difficulty getting painter's tape to stick on the slick modern surface treatment. Just imagine the tape isn't there. Imagine, as well, there are two of the wide—four inch—stripes a couple of inches apart. Or more than two. Or the wide ones and the narrow ones—3/4 inch—in exchanged locations. Or the narrow ones only, or the wide ones only. Or one wide one down the middle with an arrow point made with wide tape, angling over the fender tops to a spot above the wheel centers. (Fearless John Surtees tribute?)

So far, I like it best with no stripes. Haven't tried the quarter- and eighth-inch pinstripe widths, yet.

 

[Chef jpd]

How much are the Bullitt fuel rail covers?

They were $125, but included those big hoses that lay on them (which are not needed)

 

[Decanes]

How's your ammo supply, notice extra mags were empty. Getting tough in my area

it is very hard to find ammo here
got good stock on 5.56 3k
running very very short on 9mm about 250

 

[Decanes]

Spent a few minutes irritating the Gray Car with pieces of my supply of Orange Reflective Vinyl Tape. Thinking about striping it one way or another. Possibilities are unlimited.

I had some difficulty getting painter's tape to stick on the slick modern surface treatment. Just imagine the tape isn't there. Imagine, as well, there are two of the wide—four inch—stripes a couple of inches apart. Or more than two. Or the wide ones and the narrow ones—3/4 inch—in exchanged locations. Or the narrow ones only, or the wide ones only. Or one wide one down the middle with an arrow point made with wide tape, angling over the fender tops to a spot above the wheel centers. (Fearless John Surtees tribute?)

So far, I like it best with no stripes. Haven't tried the quarter- and eighth-inch pinstripe widths, yet.

looks great with out

 

[shogun32]

would 20mm make them flush in front? (19x9.5 20mm)

basically, yes.

 

[shogun32]

running very very short on 9mm about 250

I should go to the Capital Gun Show and sell some out of the trunk like it's contraband or something...

Sponsored