What did you do to your S550 Mustang today?!

[K-Roll302]

What does the dealer say about it?

They only know about my hood problem. I just saw this tonight. We'll have to wait and see what they say tomorrow. I do know that there's no way this should be happening on a year old car. What's stranger is that I'm sure this part of the car is steel. And I was pretty sure only aluminum bubbles like this.

Sponsored

 

[2morrow]

Got some new wheels thanks to [MENTION=14702]CarlosMRRDesignWheels[/MENTION] & MRR Design Wheels and just mounted them today. 20x10 +35 with MPSS 275/35/20 Front and 20x11 +50 and 295/35/20 K1 rear.

I'll take some good pictures soon.

 

[ronnieb1958]

Got some new wheels thanks to [MENTION=14702]CarlosMRRDesignWheels[/MENTION] & [MENTION=8058]MR[/MENTION]R Design Wheels and just mounted them today. 20x10 +35 with MPSS 275/35/20 Front and 20x11 +50 and 295/35/20 K1 rear.

I'll take some good pictures soon.

nice...and please do a side shot.

 

[2morrow]

nice...and please do a side shot.

Ask and you shall receive...

 

[plc268]

Yup, took a few more as I was leaving today.

I love that carbon fiber center console as well. Personally I'm considering getting it in matte carbon so it doesn't stand out too much. :love:

 

[ied0135]

Nothing to the GT today. The truck has been neglected for a month or so since picking up the car. Washed the truck and did a quick detail. Tomorrow will be the Mini and the GT and the an afternoon drive to the pub.

Jesus, get some color in your life man!

 

[Boston23]

Jesus, get some color in your life man!

Lol. At one time it was black trucks and black cars but they were a bitch to keep clean and detailed. Silver hides dirt better than any other color IMO.

 

[wireeater]

Late night pictures since its been a while

:eyebulge: That is a lot going on inside of there, damn. :lol: What gauges are you running? (readings)

 

[Davepurp]

Finally got around to taking my front bumper off again to Swap out my grills for the RTR and get my MAK Powerpipe installed on the Procharger. Havent checked the mechanical guage yet, but my logs are showing a great increase on Flow Rates across the board. Very pleased


Hope to get it back on the dyno as soon as weather cools down to see what its really doing

 

[racered_ppGT]

finally some new wheels to replace the stock PP ones
20x10 and 20x11 on Eibach Sportline springs.

 

[Xavier]

Putting my MGW shifter into reverse after chest and back day at the gym = torture. Especially when you have to do it twice because you jacked up your parking job.

Buy one if you need some motivation to get swole.

 

[jvandy50]

Putting my MGW shifter into reverse after chest and back day at the gym = torture. Especially when you have to do it twice because you jacked up your parking job.

Buy one if you need some motivation to get swole.

lol no doubt! and forget using if in rotator cuff repair rehab:cheers:

 

[Mootang]

:eyebulge: That is a lot going on inside of there, damn. :lol: What gauges are you running? (readings)

Lol, yea I get that a lot too. Gauges in the center are Prosport Evos readings from left to right: boost, oil pressure, and fuel pressure. All three sitting inside a Shelby carbon fiber gauge pod. The A-Piller on the drive aide are Aeroforce gauges and reading from the OBDII. Currently those are just reading MPH, RPM, Battery, and Fuel Line. I change the readings on those form time to time to read more about the engine and cylinder heads.

I am debating on switching the Prosport Evos out for Tanabe Revel OLED gauges, but haven't decided yet lol.

Sponsored