What did you do to your Mach 1 today

[JOKER M1]

This got me thinking about removing the emblems from the fenders and incorporating it into the stripes.... .

Well hmmmm, I can picture that looking good.

Sponsored

 

[NJMike]

Very sweet! Congrats. Thread for this? Very curious of your impressions

 

[2022 Mach 1]

Very sweet! Congrats. Thread for this? Very curious of your impressions

I work on one in he coming days. Lots of rain unfortunately right now.l amd exhausted after a 10 hr day to get it 1t impression on the 3hrs home were good. Embarrassed a track hawk and new raptor R and still knocked down 22 mpg doing mostly 80 with a few 60 to 130 pulls. Broke the tires loose on a 7k paddle shift from 4th to 5th.

Mike I think once you can ring it out past 5k you'll have a better experience on the performance side.

 

[Jimmy Dean]

after 9 months I finally found the steering wheel heater.

 

[MACHtobers Very Own]

Well hmmmm, I can picture that looking good.

I'm curious of this too. I took my fender emblems off cause I felt it was too much but in that grey space might work out nice.

 

[JOKER M1]

I'm curious of this too. I took my fender emblems off cause I felt it was too much but in that grey space might work out nice.

I think @Tinpot may be on to something there, put the Mach 1 (in anthracite matte) on the black in the front fender then move the chassis number around back in smaller font. Don’t think I would do both on the side of the car

 

[NJMike]

Embarrassed a track hawk

Mike I think once you can ring it out past 5k you'll have a better experience on the performance side.

I hope to see it perform once I can get the RPM up.
I am somewhat pleasantly surprised to hear that about the tooling around. I will test this if I can find a competent driver for my Jeep. Assuming this was from a roll, what was the (rough) MPH?

 

[cerbomark]

LOL, I was onto something a while ago but not as smart as some.

 

[2022 Mach 1]

I hope to see it perform once I can get the RPM up.
I am somewhat pleasantly surprised to hear that about the tooling around. I will test this if I can find a competent driver for my Jeep. Assuming this was from a roll, what was the (rough) MPH?

He jumped on it when we were both doing 75 and pulled out a car length as i wasnt expecting to go. I had two to three car lengths by 130 easily. This car as it sits with some drag radials should easily do 10.5 or quicker.

 

[NJMike]

He jumped on it when we were both doing 75 and pulled out a car length as i wasnt expecting to go. I had two to three car lengths by 130 easily. This car as it sits with some drag radials should easily do 10.5 or quicker.

It is like a brick going that speed! I forget, what tires are you on? I still have the Cup2 but think a DR would be better

 

[2022 Mach 1]

It is like a brick going that speed! I forget, what tires are you on? I still have the Cup2 but think a DR would be better

Ps4s

 

[jabarger1]

Added my own lower decal set. My wife made them and I installed them. I did a little different pattern than the factory set up. I think it turned out pretty good. Also saved some money!

 

[2021 Mach 1]

Please post a video, love to hear and see it go. Enjoy

 

[2022 Mach 1]

Please post a video, love to hear and see it go. Enjoy

Once I have some slightly better weather sure thing

 

[2022 Mach 1]

Recommendation on catch can. JTL Ford Performance UPR or other?

Sponsored