What did you do to your GT350 today?

[FDHog]

Today I had the pleasure of changing shift knobs. The SOB who put this knob on must've used the whole tube of loctite.
Had to resort to a pipe wrench to get it off. Heat gun and strap wrenches were useless.
Also hardwired my dash cam and mirror tap for radar detector.. BMR jacking rails are sitting on garage floor for another day.

Sponsored

 

[16Kobra]

Today I had the pleasure of changing shift knobs. The SOB who put this knob on must've used the whole tube of loctite.
Had to resort to a pipe wrench to get it off. Heat gun and strap wrenches were useless.
Also hardwired my dash cam and mirror tap for radar detector.. BMR jacking rails are sitting on garage floor for another day.

Interested in how you hardwired the dash cam. can you post pictures?

Been trying to get power to my wifes EB and my 350R. Cant seem to get it correct.

I have my radar detector wired into my mirror also.

 

[FDHog]

Ran wire in headliner groove, down A pillar. When I got even with bottom of dash I went under the dash and into fuse panel.
Bottom 10amp fuse powers on when engine starts. Used a fuse tap and grounded to a bolt on the passenger side firewall.
Just pull the weatherstripping away from the trim and tuck the wires in. Hope this helps

 

[16Kobra]

Ran wire in headliner groove, down A pillar. When I got even with bottom of dash I went under the dash and into fuse panel.
Bottom 10amp fuse powers on when engine starts. Used a fuse tap and grounded to a bolt on the passenger side firewall.
Just pull the weatherstripping away from the trim and tuck the wires in. Hope this helps

yes sir it did. sounds like what the YT person did. Just need to buy the fuse tap.

thanks

 

[huskeee]

CMS bar in, along with Wilson lap belt mount. Just waiting on the Schroth to arrive

 

[09cs]

Painted my calipers yellow and took a page out of Terrance’s book, and did full clear ceramic tint all the way around

 

[datadatum]

About to re-convert my car to Lund e85. I took it off for a while, as some of local stations were flaky at maintaining their supply. (Showed up one too many times with an empty tank - not hard at 8mpg - only to have the local station OUT of e85.) This time I may just leave it in FLEX...

 

[newmoon]

Added this new Airaid CAI to the 350, install went great and I am very impressed by the quality. Car feels good, noticeable bump in the butt dyno.

https://ibb.co/DRcj9wY

 

[Amacron]

Added Rock guards

 

[Caballus]

Ordered an Anderson Composites 2019+ GT350 CF swing from Vivid Racing back in Nov before AC actually started production. Production under way now.

Very well packaged and took less than a week to arrive via U.S. mail to overseas mil address.

Dealing with AC was great--dealing with Vivid Racing not so much, as in won't order from them again.

But back to AC...

Not sure about this. Not damaged; just not smooth or precisely formed. Will figure it out when I mount it.

This side looks much better.

Surprised it didn't come with 3M tape, but that's an easy fix.

 

[Jobsi]

I ordered mine Presidents’ Day weekend and they said up to a 12 week wait for the swing I ordered thru lethal and verified the wait time with ac. I also ordered the gurney flap. I am also surprised no 3m tape and not precise underneath. My eBay one looks better underneath and came with tape
Do you have anymore pics ?

 

[Caballus]

I ordered mine Presidents’ Day weekend and they said up to a 12 week wait for the swing I ordered thru lethal and verified the wait time with ac. I also ordered the gurney flap. I am also surprised no 3m tape and not precise underneath. My eBay one looks better underneath and came with tape
Do you have anymore pics ?

Don't want to overstate the "imprecision." It's only the case with the slot, which I have no clue until I take off the OEM swing what the slot is for. Other than that it's extremely well made. Not disappointed at all.

I had a CF spoiler on my previous GT350. Got it from MAD Industry and it was perfect in every way. Unfortunately, they are no longer around.

What other pics would you like?

 

[Tomster]

-First oil change via dealer, FL 2069 filter @ $43 ....
-Alignment via dealer (tech could have done better..)
-New front hood gasket via dealer FR3Z-16A238-C at 2x price, wouldn't cover under warranty :/
-Wanted to drive it 30mi away to do bumper sag TSB, said no way and wouldn't provide TSB kit to do myself :(

I ordered 4 of the oil filters from Rock Auto for $20.79 each. A case of oil off Amazon was $102 shipped.

 

[Tomster]

Track Time on Sat

How ya diggin the new R Jim?

 

[Caballus]

By the way @Tomster, this is the swing you offered to ship. Still grateful for the offer...

Sponsored