Vicrez GT500 Hood for 2018+ Mustang! (journal)

[Zelek]

I got the Quik-Latch QL50 (2.5" round). Have not drilled or installed yet.

Did you have a chance to install these? I'm considering doing this hood for my Mach 1 with a new emblem done around the vent. I wanted to do the Quick-Latch system as well but I can't seem to find an answer on where these mount on the inside. If you do have it installed, can you show a picture of what it looks like under the hood?

Sponsored

 

[sabtaj1]

Did you have a chance to install these? I'm considering doing this hood for my Mach 1 with a new emblem done around the vent. I wanted to do the Quick-Latch system as well but I can't seem to find an answer on where these mount on the inside. If you do have it installed, can you show a picture of what it looks like under the hood?

I haven’t installed em as of yet. Weather hasn’t cooperated yet to get the car out of storage

 

[MCS]

This might be a good alternative for the MP Concepts GT500 that I can't get shipped to Canada (AM doesn't ship large freight like that to us).

Will need to dig through these pics a bit more then see if Vicrez will ship to me here.

 

[shogun32]

This might be a good alternative for the MP Concepts GT500 that I can't get shipped to Canada (AM doesn't ship large freight like that to us).

have it shipped to a mailbox on the other side, and then drive across and get it?

 

[MCS]

They ship to Canada!!!!

Now I just need to make sure that my paint and body place will let me ship it right to them, have them paint it before I bring the car in etc.

 

[MCS]

Got some good pics today of my car!

I've been scanning through the 5 pages of stuff but can't seem to find all the info.

Would love to see a parts list on this bad boy!!! Now that my rims, tires and lowering are scheduled for April it's time to shop for the rest of the things!!!

Hood = Vicrez GT500 for 18-21 Mustang
- Uses stock latch and hinges?
- Quick-Latch QL-50L-LP Hood Pins

Bumper = I read somewhere it was a 777 front bumper? Can you confirm? Thinking IKON myself

Spoiler = That looks like a GT500 rear spoiler. You just remove your factory one and bolt on the new one?

 

[sabtaj1]

Finally installed the hood today. Turned out great. Just set the fake pins on for now until I can verify there’s a place to mount the pins for the quick latches. I’ll have to get a couple pics of underside as I didn’t use the crap hardware they supplied.

 

[MCS]

She looks great man!!!!

I'm guessing you didn't use the rain tray? No touchless car wash for you eh? LOL

What front bumper are you running? It looks like you've lowered your car at least an inch so curious to see what the bumper is.

 

[sabtaj1]

She looks great man!!!!

I'm guessing you didn't use the rain tray? No touchless car wash for you eh? LOL

What front bumper are you running? It looks like you've lowered your car at least an inch so curious to see what the bumper is.

Well, I used my own hardware to mount the vent to the hood. It’s pretty trick. And where the raintray mounts I used rivet nuts and attached them to the vent and have knurled finger screws to take the rain tray off n on with ease if needed when washing or if rain may be coming when out. I’m running the BMR drag springs and it’s the PP1 with the lower piece from eBay that was like 115$ shipped. The one piece lip.

 

[RonsterGT]

This might be a good alternative for the MP Concepts GT500 that I can't get shipped to Canada (AM doesn't ship large freight like that to us).

Will need to dig through these pics a bit more then see if Vicrez will ship to me here.

Sign up with CrossBorderPickups.com.
Items delivered to Niagara Falls, NY. From there, CBP will bring over border to Mississauga or Markham (your choice). You can then pick up at either location or have shipped to you.
I always choose ship to me, since I'm in Peterborough.
Easy.

 

[Zelek]

Looking at the lines of the hood above, I don't know that the Mach 1 emblem is going to follow it well towards the front to the bumper. Looks like part of it will bend over the lines some.

 

[waltematech]

Looking at the lines of the hood above, I don't know that the Mach 1 emblem is going to follow it well towards the front to the bumper. Looks like part of it will bend over the lines some.

yea, the Vicrez hood has those bends, but they’re really unnoticeable under decals. I was worried about that too with my GT500 stripes, but after they were put on, you really can’t tell at all.

 

[Zelek]

yea, the Vicrez hood has those bends, but they’re really unnoticeable under decals. I was worried about that too with my GT500 stripes, but after they were put on, you really can’t tell at all.

I may just go for it anyway because I really like the hood and it should also eliminate any sort of flutter at high speeds which is one downside of the 2018 hood with no real vents. I think the OEM Mach 1 decal can still work.

 

[TrackMustang]

Are these Big Worm? If so are they narrow or wide?

 

[MCS]

Are these Big Worm? If so are they narrow or wide?

I think they look great! Surely there must be a page on the internet with the specs fo the GT500 stripes? "Thou dost have stripes that are only X inches in width and Y inches apart. Not more and not less"

Sponsored