Step by Step Guide to Enabling Blind Spot Information System (BLIS) and Cross Traffic Alert (CTA)

[rubens_5.0]

what bolts did you guys use for the bracket that goes to the car

Sponsored

 

[Blade007]

you can get this part W714293S424 in place of the bolts

 

[Chappers]

This may have been covered, but does anyone know what the pigtail connector is for the OEM mirror LED? For BLIS?

 

[Falk03]

WPT-1197 / 3U2Z-14S411-PFB

or

JST JPWF 02R-JWPF-VSLE-S for the housing and JST JWPF BWPR-001T-P0,25 for the terminals.

 

[rubens_5.0]

WPT-1197 / 3U2Z-14S411-PFB

or

JST JPWF 02R-JWPF-VSLE-S for the housing and JST JWPF BWPR-001T-P0,25 for the terminals.

do you need to buy 2 of each of these pigtails for oem mirrors with blis and do the alert wires go crimped to this?

 

[rubens_5.0]

also the 2 part numbers for the mirrors FR3Z17K707D, FR3Z17K707G Have no blis i ordered one and didnt come with it i saw these too that say on the ford parts website that they have blis and memory and heat idk if this would work the same?FR3Z17K707R FR3Z17K707Q

 

[terion]

EM2Z-14C689-A from the guide is listed as from Ford Edge. Mustang’s is FT4T-14D453-AC. Are they absolutely same? Also left and right don’t differ?

 

[buzz-dee]

Left or right doesn’t matter. One of the modules (right hand side) wirings has two ground wires instead of one. That way the module itself „knows“ which side of the vehicle it is located at and will identify itself on the can-bus accordingly.

 

[KKJMG]

In my case i ran 4. One pair for the BLIS light and another pair for the heated mirror. If you already have heated mirror then you only need 2.

Blade, where did you get power/control for the heated mirrors? I'm upgrading a base model to BLIS and heated mirrors. Thanks!

 

[Blade007]

Blade, where did you get power/control for the heated mirrors? I'm upgrading a base model to BLIS and heated mirrors. Thanks!

So @Falk03 helped me with this. I joined both wires for both mirrors and connected them to yellow and blue wire in the connector that is above the C215 connector if I remember correctly.
Here is a wiring diagram that helped.
I can't get to the car to take a picture unfortunately as it's buried in snow

 

[KKJMG]

In my case i ran 4. One pair for the BLIS light and another pair for the heated mirror. If you already have heated mirror then you only need 2.

Blade, where did you get power/control for the heated mirrors? I'm upgrading a base model to BLIS and heated mirrors. Thanks!

 

[KKJMG]

Blade,

Thanks! What turns the heat on and off?

 

[Falk03]

Blade,

Thanks! What turns the heat on and off?

The heated rear window switch :-)

 

[KKJMG]

The heated rear window switch :-)
So its blue on one side yellow on the other as in the diagram and each grounded. No need to go to the heated rear window switch? Thanks!

Jim

 

[Falk03]

So its blue on one side yellow on the other as in the diagram and each grounded. No need to go to the heated rear window switch? Thanks!

Jim

In my case the wires were already present at the door connectors and I have a MY16 base model. To be exactly the wire colors should be yellow+blue and yellow+green.
A general warning: be careful with wire colors as they might be different. Both wires start in C215 #8 and go to the door connectors: C311 #B8 and C313 #A1.

Anyway the heated window switch wouldn't help you. It just talks to the BCM via the CAN bus. The BCM provides power to the heated window.

Hope this helps.

Sponsored