So you wanted to go fast and have a track car?

[Proshop]

Can’t believe I missed your build thread! So you decided to finally go with comp after all? Did you finally get a compressor map from them or just say fuck it?

Sponsored

 

[illtal]

Can’t believe I missed your build thread! So you decided to finally go with comp after all? Did you finally get a compressor map from them or just say fuck it?

Funny thing is that I have a few of comps turbo compressor maps. The fact that they won't give me the ones I wanted for this project pissed me off.

I got these on Black Friday sale.

I wanted to do borgs but they are all on backorder.
Weighing out turbos I still believe Borg is the best. But man an oil leak down low would not fun. I decided to not roll the dice on that an go with these.

These are oversized, mainly because of the ported heads and extra revs. Doesn't matter if they come in "late".

Still probably gonna run meth on gas. So I don't have to deal with the e-85 restrictions.

 

[illtal]

Update car will go out next week. Builder will do the install and take pix as well. I've been a bit

New parts to be installed:

Radium Fuel hat
2 Fuelab 496 brushless fuel pumps
2 Fuelab pwm controllers
2 comp turbo 6467
2 gbf 44 mm wastegates
1 gbf 52mm bov
Scherer fab intercooler (great piece)
TKM 5.2L 12:1 compression short lock
Cometic MLX 44mm heasgaskets
Frankenstein ported gen3 heads
Valvesprings and retainers
Custom intercooler piping
Fuelab electronic fuel pressure regulator

Optional/still thinking/need
ID1700x injectors or FIC1650
Stock intake manifold vs sheet metal manifold
Aftermarket fuel rail or one on said manifold
Clutch -> some ideas
Upgraded MT82 / MagnumXL -> leaning MT82
Steeda bump steer kit or combo control arm kit



Unaddressed areas:
Boost controller -> I have one I want it's not available yet
Axles -> I don't launch this car *yet
Driveshaft -> same as above
Brakes -> wildwood or ap racing or combo


Installed parts
Front coilovers with pillowball camber plate
Rear steeda drag springs
Rear Vi-king handling shocks with solid mount
Rear billet camber arms
Cradle lockout kit
Savini SV-F 5

 

[aham23]

loving those wheels. nice stang.

 

[illtal]

Car has been sent off to the shop will see it in a few months....

 

[illtal]

loving those wheels. nice stang.

Thanx boss

 

[illtal]

*** gen3 heads

So in case you guys do any head work and need to replace parts.

The followers that need to be used is the predator part. M-6564-M52A

The lifters are the normal part common to all coyotes sans voodoo. M-6500-M50

 

[VictorH]

Super cool build! Don't finish it and then decide you're going to sell it. Have some fun, that thing is going to be a monster. When you say track, is this a drag car or circuit-type track car?

 

[illtal]

Super cool build! Don't finish it and then decide you're going to sell it. Have some fun, that thing is going to be a monster. When you say track, is this a drag car or circuit-type track car?

Both.... Well more like a 1/2 miler and more circuit. It will likely never dawn a set of drag* slicks. (Circuit tires are fine) The goal is to have a car that can be full weight and do it all.

 

[NJMike]

Very cool build - following.
For intake what about a Mach 1/GT350? I happen to have one I wont be using

 

[illtal]

Very cool build - following.
For intake what about a Mach 1/GT350? I happen to have one I wont be using

I might take you up on that if I don't go full dumb and buy something like a plazmamann

 

[illtal]

Ended up going with FIC 1650cc injectors and since holley is giving away coyote fuel rails for 89 USD I had to do it....

 

[NJMike]

Hoping you get some photos soon

 

[illtal]

Hoping you get some photos soon

I'll call up the installer, he has everything now but haven't shared status with me yet.
I normally check every two weeks or so. He did tell me he didn't want to build it without being able to completely close up the engine.

 

[illtal]

I'll call up the installer, he has everything now but haven't shared status with me yet.
I normally check every two weeks or so. He did tell me he didn't want to build it without being able to completely close up the engine.

I'm in town gonna take a fawkload of S550 porn shots. Hopefully I can get to it this weekend.

Sponsored