Sponsored

Project: 2017 Mustang GT Coyote Smurf

OP
OP
17again

17again

Well-Known Member
Joined
Jul 22, 2017
Threads
5
Messages
94
Reaction score
70
Location
Dallas, TX
First Name
Vince
Vehicle(s)
2017 Mustang GT Grabber Blue
I may try that, I just checked my mirror covers again and they are pretty close in color so it would look real close. I suppose if I really mess up I can just peel it off and try again.
Sponsored

 
OP
OP
17again

17again

Well-Known Member
Joined
Jul 22, 2017
Threads
5
Messages
94
Reaction score
70
Location
Dallas, TX
First Name
Vince
Vehicle(s)
2017 Mustang GT Grabber Blue
Got this shock brace in the mail from eBay for on $65 plus $25 shipping! Can't wait to put it on. Already had the 2 nuts needed to install
shock tower brace.jpg
 
OP
OP
17again

17again

Well-Known Member
Joined
Jul 22, 2017
Threads
5
Messages
94
Reaction score
70
Location
Dallas, TX
First Name
Vince
Vehicle(s)
2017 Mustang GT Grabber Blue
Lighted sill plates from ebay for $35. Still had factory plastic covering the chrome lighted section. I cut off connector and wired by hand.

20180915_143653.jpg
 
OP
OP
17again

17again

Well-Known Member
Joined
Jul 22, 2017
Threads
5
Messages
94
Reaction score
70
Location
Dallas, TX
First Name
Vince
Vehicle(s)
2017 Mustang GT Grabber Blue
Installed a standard GT350 wheel. I preferred this over the R because of the white stitching. With the paddle shifters it's an extra step or two but it was way easier than I thought. Last time I replaced a steering wheel it was on steering spline shaft and needed a puller to get it off. Took about an hour to do from start to finish, but being paranoid I left the battery disconnected for an hour before starting. The steering wheel is what you handle most in the car, it should be the best.

20190217_173830.jpg
 
OP
OP
17again

17again

Well-Known Member
Joined
Jul 22, 2017
Threads
5
Messages
94
Reaction score
70
Location
Dallas, TX
First Name
Vince
Vehicle(s)
2017 Mustang GT Grabber Blue
Added my GT/CS front splitter finally after having it for a month. Install was easy, took less than an hour including putting the car on jacks. Didn't need to remove the front wheels and just had to move the front fender liners to the side a little to get access to one screw on each side. Now my Sto-N-Sho license plate holder is too short but I am modding that and should be done tomorrow. Really happy with the looks but I'd like to find some splitter fins for the sides if somebody makes them.

20190427_080600.jpg
20190427_080551.jpg
20190427_084814.jpg
20190427_084826.jpg
20190427_085411.jpg
 

Sponsored

OP
OP
17again

17again

Well-Known Member
Joined
Jul 22, 2017
Threads
5
Messages
94
Reaction score
70
Location
Dallas, TX
First Name
Vince
Vehicle(s)
2017 Mustang GT Grabber Blue
Here is my modified Sto-N-Sho license plate holder. They are $84 so I didn't wan't to buy a new one, I just extended the Base Mustang version to be 1 3/4" longer to fit.
20190428_093833.jpg
 
OP
OP
17again

17again

Well-Known Member
Joined
Jul 22, 2017
Threads
5
Messages
94
Reaction score
70
Location
Dallas, TX
First Name
Vince
Vehicle(s)
2017 Mustang GT Grabber Blue
My $8 eBay engine mod
20190915_101832.jpg
20190915_102014.jpg
20190915_103250.jpg
20190915_103254.jpg


20190915_110419.jpg
Sponsored

 
 




Top