No - just terribly poor driving, probably worst this year. I would want to blame it on ~160 runs old tires but really can't, no matter how hard I try. Suspension worked fine after I got rid of the fault by disconnecting battery in the grid, just freaked me out a bit since I had zero time to attempt anything other than battery disconnect.Suspension woes?
Thanks a lot Tim.An email has been sent.
I’m sorry to hear the mechanical trouble got in your head, I’ve been there.No - just terribly poor driving, probably worst this year. I would want to blame it on ~160 runs old tires but really can't, no matter how hard I try. Suspension worked fine after I got rid of the fault by disconnecting battery in the grid, just freaked me out a bit since I had zero time to attempt anything other than battery disconnect.
Nightmaremoon did great, placed 6th I believe And there was hell of a lot good drivers here and lots of fast cars, including two ZLEs
Thanks a lot Tim.
Hi. I have the same exact fault and my Drive Modes are not available. I haven't yet troubleshot yet. What were some of these causes?Some sort of Uxxxx code woulda popped up. Did you still have your drive modes ?
A damaged suspension sensor would be the most common. You're using the stock controller, correct?Hi. I have the same exact fault and my Drive Modes are not available. I haven't yet troubleshot yet. What were some of these causes?
Stock controller?A damaged suspension sensor would be the most common. You're using the stock controller, correct?
As opposed to the aftermarket DSC Magneride controller.Stock controller?
Got it. Thank you for the helpAs opposed to the aftermarket DSC Magneride controller.
Hey guys, I encountered the same suspension fault message. I am on Steeda lowering springs, drove completely fine for a month. All connectors are good. Codes were able to clear apart from a U0416:00-2F code: “Invalid Data Received from Vehicle Dynamics Control Module” and it shows up as a continuous memory DTC. Any help?I did a thorough post winter drive inspection and discovered my left Magneride sensor arm connector disconnected. I forgot to reconnect after I torqued my Camber arm bolt during my winter mods. After reconnecting, I deleted duct faults and then I Drove 10 miles to fully reset my BCM and everything works fine. Thank you for your help.
Do you have Magneride? If so, I think you have to re-adjust for the lowering. I have also read where if they go to low Magneride will fault. Good LuckHey guys, I encountered the same suspension fault message. I am on Steeda lowering springs, drove completely fine for a month. All connectors are good. Codes were able to clear apart from a U0416:00-2F code: “Invalid Data Received from Vehicle Dynamics Control Module” and it shows up as a continuous memory DTC. Any help?
Yes, I have magneride in my PP2. Steeda springs only lowered the car about 1”. Compatible springs with magneride. Don’t think the springs are the issue. Also read that at least 15 cold starts and run up to normal operating temperature within a 200 mile period is when the continuous memory resets. Might have to bring it into Ford if it doesn’t go away then.Do you have Magneride? If so, I think you have to re-adjust for the lowering. I have also read where if they go to low Magneride will fault. Good Luck
Forgot to note, I also did to a ride height calibration through my code scanner. Still didn’t make it go awayDo you have Magneride? If so, I think you have to re-adjust for the lowering. I have also read where if they go to low Magneride will fault. Good Luck
For me, the codes which clean are usually collateral faults, but the hard code fails usually point to the cause. Good luckUpdating for anyone following this thread, these are the codes that came up on my OBDII scanner. Was able to clear the C110D:13-AF code momentarily, but would come back on. The other PCM code stayed on in the continuous memory and couldn't be deleted. I tried disconnecting the battery for 45 mins and no luck either. Luckily I'm about 40 mins away from Galpin Ford, so the car is in service now being checked out. Hopefully it's just a code they can erase and not have to order any parts. Will update more here on how it goes.