GT500 Oil Pan HV Pump M-6675-M52S

[EFI]

These gap will close up with engine heat.

That's very true, however most clearances are measured and set at cold temps. If it's loose cold, you can't just rely on heat to close up the gap.

Sponsored

 

[ice445]

That's very true, however most clearances are measured and set at cold temps. If it's loose cold, you can't just rely on heat to close up the gap.

Someone's ex needs to hear this.

 

[Schwerin]

Thanks for the part number I've added it to the sheet

 

[Five_0_Ford]

Just for search results sake, I thought I would start a thread dedicated to swapping the 2020 GT500 Oil pan and HV Pump into the GT's. Mine arrived today and it's a 19lb beast. I'll be doing the install next week so I'll post progress when there's anything exciting. Along with the Pan and OP, I'll also be doing the Steeda Road Race K-member at the same time.

2016 GT w/ LTH Long tube headers. Fitment of the pan might be tight but I have lots of hammers and prybars, lol.

Any updates? Did you get this installed, I'm looking to do it on 2015 with LTH longtubes

 

[Wolvee]

Any updates? Did you get this installed, I'm looking to do it on 2015 with LTH longtubes

the update is, I bought a gt500 and I’m selling all my parts, lol. I never got them installed.
Edit: let me know if you want them, I’ll make you a deal with Oil Pump gears.

 

[olaosunt]

So far Boundary had the greatest gap at .007 but comparing directly to the MMR's might be Apples to oranges because the boundary's are for Coyote/Voodoo and the MMR's are for the Predator. I'll get the other half of the measurements this week. I'm not sure of the needed specs for each.

These gap will close up with engine heat.

the update is, I bought a gt500 and I’m selling all my parts, lol. I never got them installed.
Edit: let me know if you want them, I’ll make you a deal with Oil Pump gears.

I am interested .
billet OPG ‘s right .
How much ?

 

[Wolvee]

I am interested .
billet OPG ‘s right .
How much ?

I sent you a PM.

 

[Bahndvr]

It would have driven me crazy if I didn’t change my opg’s in my GT500 oil pump (installed Boundary Black OPG) when I did this mod but I know some feel comfortable not. My Kooks headers were close on the drivers side but ultimately of no concern. The only modification you’ll have to do is extend the wiring for the pan sensor since it’s now on the opposite side. It’s been problem free on street and road course these last 6 months. Oil changes cost more now going from 8 to 11.5 qts.

Which Boundary Black OPG did you buy, 2011+ Ford Mustang or 2020 GT500?
Thanks

 

[db252]

Which Boundary Black OPG did you buy, 2011+ Ford Mustang or 2020 GT500?
Thanks

If you get the GT500 oil pan and pump kit you have to order the 2020 GT500 opg.

 

[Bahndvr]

If you get the GT500 oil pan and pump kit you have to order the 2020 GT500 opg.

I ordered and now have the M-6675-M52S. Just want to get everything together for install.
Thanks

 

[Bahndvr]

What are the torque specs for the 8 Torq bolts in the oil pump housing?

 

[Bahndvr]

It would have driven me crazy if I didn’t change my opg’s in my GT500 oil pump (installed Boundary Black OPG) when I did this mod but I know some feel comfortable not. My Kooks headers were close on the drivers side but ultimately of no concern. The only modification you’ll have to do is extend the wiring for the pan sensor since it’s now on the opposite side. It’s been problem free on street and road course these last 6 months. Oil changes cost more now going from 8 to 11.5 qts.

What sizes header tubes?

 

[Bahndvr]

What gasket (maker) to use for the oil pan?
Chilton says: Install the new oil pan baffle and gasket.

 

[Brazos609]

What gasket (maker) to use for the oil pan?
Chilton says: Install the new oil pan baffle and gasket.

The windage tray that comes with the pan is your gasket.

 

[Bahndvr]

The windage tray that comes with the pan is your gasket.

Oh, I guess I didn't look close

I'm going to take it to a shop and have them install; just want to make sure they don't need anything

Sponsored