Sponsored

Gen 3 2.9L whipple dyno results

Platinum_5.0

Well-Known Member
Joined
Jan 8, 2018
Threads
12
Messages
415
Reaction score
190
Location
Edmonton, Canada
First Name
Daniel
Vehicle(s)
2021 10R Whipple
For almost 16psi it kinda seems low. At 14.8psi on my Gen 3 Whipple we are estimating 880ish whp. The car trapped 141 at 3800DA and was falling over hard on the shifts with clutch issues. Expecting to do 143-144 in the spring with the issues fixed.
Sponsored

 

sloride

Well-Known Member
Joined
May 20, 2017
Threads
9
Messages
207
Reaction score
66
Location
ohio
Vehicle(s)
2016 GT
For almost 16psi it kinda seems low. At 14.8psi on my Gen 3 Whipple we are estimating 880ish whp. The car trapped 141 at 3800DA and was falling over hard on the shifts with clutch issues. Expecting to do 143-144 in the spring with the issues fixed.
The car only went to 6,100rpm. Dyno speed limited. I’m guessing another 1500rpm that number would have been higher
 

Platinum_5.0

Well-Known Member
Joined
Jan 8, 2018
Threads
12
Messages
415
Reaction score
190
Location
Edmonton, Canada
First Name
Daniel
Vehicle(s)
2021 10R Whipple
The car only went to 6,100rpm. Dyno speed limited. I’m guessing another 1500rpm that number would have been higher
🤦‍♂️ My bad, I totally overlooked that. Yeah 800 at 6100 is solid. I rev mine to 8000. You would be right up there for sure👍
 

Sponsored

OP
OP

cmxenon3333

Active Member
Joined
Jun 2, 2020
Threads
9
Messages
38
Reaction score
6
Location
New York
First Name
Warren
Vehicle(s)
2017 Mustang GT
For almost 16psi it kinda seems low. At 14.8psi on my Gen 3 Whipple we are estimating 880ish whp. The car trapped 141 at 3800DA and was falling over hard on the shifts with clutch issues. Expecting to do 143-144 in the spring with the issues fixed.
Mustang dyno or dynojet? SAE corrected or uncorrected?
 
OP
OP

cmxenon3333

Active Member
Joined
Jun 2, 2020
Threads
9
Messages
38
Reaction score
6
Location
New York
First Name
Warren
Vehicle(s)
2017 Mustang GT
The car only went to 6,100rpm. Dyno speed limited. I’m guessing another 1500rpm that number would have been higher
I would have to guess that it would've been higher too
 

Platinum_5.0

Well-Known Member
Joined
Jan 8, 2018
Threads
12
Messages
415
Reaction score
190
Location
Edmonton, Canada
First Name
Daniel
Vehicle(s)
2021 10R Whipple
Mustang dyno or dynojet? SAE corrected or uncorrected?
I haven't had it on the dyno yet on the 3.2 pulley (14.8PSI) but the trap speed tells the story. 4008lbs with me in the car, hurt MT-82 and still trapped 141 in 3800DA. If the transmission could shift properly I'd probably be seeing 143-144MPH which puts me around 850-880ish whp. If he is at 800whp at only 6100RPM then he is most likely 900whp at 7800-8000. Just my guess:thumbsup:
 
OP
OP

cmxenon3333

Active Member
Joined
Jun 2, 2020
Threads
9
Messages
38
Reaction score
6
Location
New York
First Name
Warren
Vehicle(s)
2017 Mustang GT
I haven't had it on the dyno yet on the 3.2 pulley (14.8PSI) but the trap speed tells the story. 4008lbs with me in the car, hurt MT-82 and still trapped 141 in 3800DA. If the transmission could shift properly I'd probably be seeing 143-144MPH which puts me around 850-880ish whp. If he is at 800whp at only 6100RPM then he is most likely 900whp at 7800-8000. Just my guess:thumbsup:
I wish I was able to take it to 8k rpms :( I probably would be around 850 is what I would guess
 

Sponsored

Platinum_5.0

Well-Known Member
Joined
Jan 8, 2018
Threads
12
Messages
415
Reaction score
190
Location
Edmonton, Canada
First Name
Daniel
Vehicle(s)
2021 10R Whipple
 




Top