285/35/19 stock suspension pics please

[abmobil]

Please post pics of your cars with that setup. Trying to decide if that’s the tire size I want to go with. I just ordered SVE SP2 wheels.

I’m also considering a 295 for the rear tire. Wheel width is 10 all the way around.

Sponsored

 

[gadgtfreek]

285/35/19 front 19x10 SVE
305/35/19 rear 19x11 SVE

 

[LSchicago]

Here's stock suspension 285/35 front, 325/30 rears.

 

[Mach VII]

283/35/19 on 19x10" wheels, stock suspension...

 

[coz0502]

I know you said stock suspension but figured I'd give you some perspective on almost the same set up (285/35/19 up front & 305/35/19 rears) with a 1in drop. No issues with rubbing, also have camber plates up front and camber bolts in rear from BMR.

 

[NightmareMoon]

285/35R19 square on 19x10 ET35 wheels (~5mm spacer on the front) and stock PP springs, so stock ride height.

Nothin wrong with 285s!

 

[Rodpwnz]

285/35R19 square on 19x10 ET35 wheels (~5mm spacer on the front) and stock PP springs, so stock ride height.

Nothin wrong with 285s!

In these pictures, you are on stock PP1 suspension without magneride? Looks pretty good! Got any more pictures to share that would show the wheel gap?

I just have to say, this thread has been very helpful in my decision of 19x10 vs 19x11 square SP2 wheels on a PP1 with magneride. If I were to do lowering springs, then I might as well go 19x11 with camber plates. But if only wheels, then 19x10 and leave it alone would be the ideal route. Just need to figure out if the ride height is going to be OK with the 19x10s...

I was worried since the 285/35r19 tires are smaller diameter than the stock PP1 255/40r19 + 275/40r19 tires, and might increase wheel gap noticeably. I'm on PP1 magneride, so I believe my wheel gap would be slightly less than yours as well(about .25 inch).

Here is a thread showing the difference between PP1 with magneride and PP1 w/o magneride: https://www.mustang6g.com/forums/threads/magneride-vs-pp1-ride.135168/post-2805750

 

[abmobil]

Thanks for the replies everyone. I ended up doing the 19x10 285/35/19 square with Michelin Pilot sport AS3+. I’m very happy with the way it turned out.

 

[NightmareMoon]

In these pictures, you are on stock PP1 suspension without magneride? Looks pretty good! Got any more pictures to share that would show the wheel gap?

I just have to say, this thread has been very helpful in my decision of 19x10 vs 19x11 square SP2 wheels on a PP1 with magneride. If I were to do lowering springs, then I might as well go 19x11 with camber plates. But if only wheels, then 19x10 and leave it alone would be the ideal route. Just need to figure out if the ride height is going to be OK with the 19x10s...

I was worried since the 285/35r19 tires are smaller diameter than the stock PP1 255/40r19 + 275/40r19 tires, and might increase wheel gap noticeably. I'm on PP1 magneride, so I believe my wheel gap would be slightly less than yours as well(about .25 inch).

Here is a thread showing the difference between PP1 with magneride and PP1 w/o magneride: https://www.mustang6g.com/forums/threads/magneride-vs-pp1-ride.135168/post-2805750

in those pics the car is stock ride height/stock PP springs, but… a 5mm front spacer in the top pic with a little more than stock camber (slotted front koni struts).

bottom pic is similar - stock ride height and springs but probably no spacer in that one.

Sponsored