2016 Trans and diff cooler

Is there a way to easily tell if the 16 came with the trans and diff cooler? I tried a couple searches but couldn't find what I was looking for.

rushca01 said:

Is there a way to easily tell if the 16 came with the trans and diff cooler? I tried a couple searches but couldn't find what I was looking for.

Click to expand...

Transmission cooler, etc., is Track Pack on the 2016.

dkbluedevil said:

Transmission cooler, etc., is Track Pack on the 2016.

Click to expand...

Next noob question..how do I know if it has the track pack?

Bigger spoiler, Recaro seats, small dash screen. That assumes the car is not a base that has had its spoiler swapped. Tech Pack has the leather seats and big touch screen.

Or you can look into the lower right/pass side nacelle on the front bumper to see if the trans cooler is there. It is visible from the outside.

rushca01 said:

Next noob question..how do I know if it has the track pack?

Click to expand...

Did you say noob? You've got some good info so far. This might help get up to speed in general...

https://www.mustang6g.com/forums/showthread.php?t=89612

Is there a thread NOT older than two years anyone is aware of to make the parts order for a trans cooler kit?

This is the list Ford Performance sent me. Not sure this is what you are looking for

For 6AN lines.
Fittings at trans:
(2) 6AN x 1/2" NPT straight adaptors [Earl's 981668]
(2) 6AN x 90 degree hose ends swivel type [Aeroquip FCM4032]

Fittings at pump:
(2) 6AN ORB (O-ring boss) x 6AN [Russell 670840]
(2) 6AN x 90 degree hose end swivel type [Aeroquip FCM4032]

SS hose/hardline transition:
(2) 6AN x 1/2" tube braze fitting [Aeroquip FCM2873]
(2) 6AN straight hose ends [Aeroquip FCM1012]

Hose:
10' to 15' of 6AN stainless braided hose [Aeroquip FCA0615 for 15' length]

Pump:
(1) Weldon 9200A pump + wiring, switch, connectors.
(1) mounting bracket to be fabricated by installer

For 8AN lines.
Fittings at trans:
(2) 8AN x 1/2" NPT straight adaptors [Earl's 981688]
(2) 8AN x 90 degree hose end swivel type [Aeroquip FCM4433]

Fittings at pump:
(2) 6AN ORB x 8AN [Russell 670930]
(2) 8AN x 90 degree hose end swivel type [Aeroquip FCM4433]

SS hose/hardline transition:
(2) 8AN x 1/2" tube braze fitting [Aeroquip FCM2874] -OR- (2) 8AN x 1/2" tube adaptor [Earl's 165008] -OR- (2) 8AN flareless tube nut [Aeroquip FCM 2498] + (2) tube ferrule [Aeroquip DCM2493]
(2) 8AN straight hose ends [Aeroquip FCM1013]

Hose:
10' to 15' of 8AN stainless braided hose [Aeroquip FCA0815 for 15' length]

Pump:
(1) Weldon 9200A pump + wiring, switch, connectors
(1) bracket to be fabricated by installer.
-----

I have question concerning pumps I know ford racing recommended
Weldon pump,when researching parts I’ve also seen people install mocal pumps briefly looking at specs gpm , temp limits are the same only difference is amps I believe Weldon is 5.5 amps and mocal is 8 .Just wondering if I’m missing something else when comparing specs.
Thanks

Why doesn’t any anyone just make a kit for this? Haha

1LE_traitor said:

Why doesn’t any anyone just make a kit for this? Haha

Click to expand...

Ford Performance does sort of.

1LE_traitor said:

Why doesn’t any anyone just make a kit for this? Haha

Click to expand...

Because Ford fixed the problem in 2017 limiting the market to sell kits to, not enough money in it to make it worthwhile. In fact I bought my car with under 300 miles on the odometer, original owner has a speed shop and bought my car with plans to make a kit. When the standard equipment was announced for the 2017 which included all coolers, he sold it to me.

What a shame.