Sponsored

Search results

  1. Best Mustang Insurer

    Fed up fighting with Admiral every renewal. Their best this year is still over £200 more than last year. GT with mods >40 14 years no claims <6k miles Live in Herts
  2. Passenger Window

    Today my passenger side window struggled to go up and down. it took several presses of the button and this was the same using the switch on either door. Has anyone experienced anything similar ?
  3. Suspension Help

    My full list of mods is here This is the current state of the suspensions alignment What concerns me the most is the front drivers side wheel is noticeably further in than the passenger side. I thought it was the camber but there's little difference between the two. Normally I would jack up...
  4. Ford Build Quality Strikes Again: 2024 Ford Mustang Caught With Mismatched Seats

    And this is why I find it hard to buy a £50k Mustang, let alone what eye watering figure the Dark Horse is going to be over here 🙁
  5. Airbag light

    FORscan code Points to the passenger side hood actuator I swapped each side over, reset the code and it still shows as passenger side. I checked the connectors and both sides are getting 1.5v. The only thing left I can think of trying is disconnecting the battery, I don't fancy pulling the...
  6. Eibach End Links Didn't Fare Well

    That's after 2 years and 4,000 miles. Both the rear look the same, haven't checked the front yet.
  7. New S650 GT or Imported GT350

    Answers on a post card please
  8. Shelby Super Snake ?

    Did they even make a RHD versions and didn't they have Roush not Whipple superchargers ? https://www.carandclassic.com/car/C1586894
  9. Car Mods, Upgrades and Repairs For 2023

    Now the weathers got better, what's everyone got planned for this year ? Upgraded oil pump and gears Upgraded crankshaft gear Upgraded harmonic balancer/damper Lightened water pump pulley Replace the rest of the pulleys, and AC and serpentine belts Replace AC condenser - current one the core is...
  10. 2016 GT PP AC Condenser

    My AC condenser has started to crumble away, it hasn't yet affected the AC performance, so I'm looking to replace it. Is there any benefit to replacing the condenser with an after market one or just stick to a new OEM Ford one ?
  11. Riddle Me This

    I've seen people using both and was wondering if there's a right or wrong answer.
  12. 2016 GT Coolant Reservoir

    Does anyone know whether the Mishimoto coolant reservoir is the same size as the Canton Racing ?
  13. No heating

    It's the first time I've used the heating in a long while as I didn't drive it last winter. Since it last worked I have done a fair amount of work on the car which has included refitting of all the coolant hoses and a coolant refill, a front mounted oil cooler fitted and a new thermostat...
  14. Mattwood

    It's a bit short notice but it's for a good cause Eventbrite
  15. Heated o2 sensors

    Should the heater control for oxygen sensors 11 and 12 both come on until they heat up and then go off, only my sensor 11 comes on and stays on ? Also heated exhaust gas oxygen sensor heater bank 1, sensor 1 and bank 2, sensor 1 come on but bank 1 sensor 2 and bank 2, sensor 2 don't. Is this...
  16. FORscan sensor logs

    Logs are from a 2016 GT I've condensed down the logs to try to make it easier to read, are these readings within an acceptable range for a 30 minute city drive ...
  17. MMR Roller Bearing Thrust System Oil Pump Backing plate

    Has anyone installed one of these, how easy was it and were there any noticeable differences ?
  18. Not seen that grille before

    Stumbled across the photo Googling for car parts - More photos here Holly Tree Cars
  19. Shaker Pro Upgrade

    My previous car had a Bose speaker system, so the Shaker Pro has always sounded poor. I'm by no means an audiophile but from what I've read nothing is plug and play, even simple speaker upgrades. I don't plan on spending thousands of pounds, so was hoping there were upgrade kits available to...
  20. Wow Dremel rotary tools are bad

    So last summer my cheapo Chinese rotary tool died after 15 years, so I decided to replace it with a nice new one. So I bought a Dremel 4300, after 6 months it started having power and speed issues so I sent it back to Dremel. They replaced it with a brand new one in February, then on Tuesday the...


Top