Search results

All parts from my 2016 GT that I recently sold. All parts are pickup in Morgantown, WV or meet up in a reasonably close distance. I will ship injectors if someone wants them. All parts make an offer. stock injectors stock intake manifold stock intake stock springs stock engine cover brand new...

As title says, sold car and these need to go. I used the control arms for about 5k miles, bumpsteer ends were never installed, so brand new. All in great shape. Looking for 300 shipped or local pickup/meet in Morgantown, WV.

How much play side to side should there be in the Tension link on the bearing side where it bolts to the subframe? I have been trying to chase down a humming sound for the past year and starting to run out of ideas. Yesterday I pulled the passenger side strut off and took it apart and...

So the drama continues. To recap had a local shop install shocks/struts, springs and the Steeda lower control arms. I am noticing a clunk from the front that happens when coming to a stop and you apply the brake with a little force. Clunk is directly affected by braking (can make it happen...

Selling my BMR SP080 lowering springs. Just removed this past week, have around 10k miles on them. Work great just went with a stiffer spring. I am currently in Sarasota FL for the next week then will be traveling back to WV. I can meet up with someone if needed around either location. Will ship...

To make a long story short, I took my car in to a shop (due to being away from home for work) to get shocks/struts, springs and the Steeda roll center correction arms and bump steer kit installed. After a week (to do a 2 day job) I finally get the car back. I was a little skeptical as I normally...

Any shops around Sarasota area that could be recommended for a shock/strut and spring install? I am down here for work the next couple of months and would like to get this done before I head back North. I currently have the OEM PP struts/shocks with BMR SP080 springs and Steeda shock mounts...

So it is time for me to buy new shocks and struts and figured I would look into changing the springs possibly while doing the install. I currently have the sp080 installed, no real complaints with them. I wouldn't mind raising the front a little bit but the back needs to stay about the same. I...

So my front end is toe'd out and the inside of my front tires are cupped. I am going to get a new alignment and replace the struts/shocks but was wondering if I could rotate the tires FR-FL (remount and balance) or if they are just completely shot now? Aside from the cupping they have plenty of...

We had an artic cold front move thru last week which dropped temperatures down in the single digits and at or below zero at night. I went and started the car and let idle up to operating temp and noticed that both O2 sensor were not reading. Tried shutting the car off then restarting and same...

Have the silver performance pack wheels that came on my car new. Rear tires are shot, one of the front has a cord busted, other is ok. One front rim is bent (can see picture) but holds air fine as picture shows. Stock TPMS are included as are the Center caps. Asking 125 picked up in Morgantown...

Swapped my Extreme mufflers (sport axle back) for a set off the Sport catback (touring axle back) last night. There was some confusion as to how to tell exactly what muffler is what, so I called up Corsa and asked. Basically if you look inside the tip section of the muffler, the Sport (touring...

What kind of headroom would I have with the 52lb injectors and a BAP running 93 octane on a centrifigual? 16 GT with 18 intake manifold.

Anyone have an issue with the fuel gauge going from 3/4 a tank back to full after sitting? I have noticed it the past couple days that it would "reset" to full (reads 99% on nGauge) then after driving a few miles starts to go back down to a real reading. It doesn't always happen but I have...

Hey all, Recently got my car aligned after installing the suspension pieces in my signature. Did the alignment with stock PP wheels/tires. Didn't get the printout but wrote down the final settings: FR Camber - -1.9 Toe - .02 FL Camber -1.7 Toe - .01 RR Camber - -2.0 Toe - -.01 RL...

When doing lowering springs, is there anything else that should be done at the same time in the rear? Basically to avoid taking stuff apart a second time. Thanks! SQ

Hi guys not real good with tire/wheel specs so wanted to run this by the more experienced guys. Looking to go with the GT7 19" 10/11 wheels with Firestone Indy 500 tires. Front 285/35/19 Rear 325/30/19. Suspension would be either BMR SP080 springs or Steeda Ultra-lite. Any issues with rubbing or...