Search results

That was my question when I opened the box. While you can get the DTC controller, parking brake switch and cup holders as separate parts, they are all included with this part. As a side note, when I ordered this part early February 2020, the price was $160. I was shocked as I thought it would...

Yes because it comes just as you see it there, with all the goodies.

That part number is KR3Z-6304567-AA and the reason it is expensive is because it comes with the DTC controller, parking brake switch and cup holders

You cannot find it because it is not available separately, at least is wasn't a year ago when I covered mine in Alcantara. It is part of the entire top console.

Tim, always fun to watch your videos. However, I didn't realize there would be so much negativity here towards this EV. Good thing I never posted any photos of mine. 😊

I have been waiting a year for someone else to post this. This was probably the first thing I noticed when I got in the car the day I drove it home. While mine is not as bad as yours because it is a darker color, I have always seriously considered painting that entire section matte black.

Absolutely, that is it. Knew that from the first photos. Taking photos of my FPB in the garage, the hood, fenders and other body parts don't look like they match either. Top lighting comes from LED lights on ceiling, side lighting (different Kelvin) comes from outside windows then there is...

I did tint one of my F150 windshields 50% and it was a bit dark for me at night. So went back to 70%. I did it for the look but wanted a little better vision at night even tough I do have all LED lighting plus light bars on the front. It’s what happens when you are old like me. Need more light...

KB, it is illegal in CA to have ANY tint on the windshield below the already tinted eyebrow at the top also the front drivers and passengers windows. However, 70% is a fairly light tint and it isn't really noticeable. I have been doing this on all my vehicles since 2007. I only go as dark as...

Another vote for ceramic tint on the windshield. I have 70% on my GT500 and both trucks (windshields).

HK, I actually never looked at these photos closely before but now that I have, I see that the rubber stops are adjusted way too high. Those stops are domed, not flat and for them to leave an impression that large on the underside of the hood, indicates there is a lot of pressure from the hood...

I'm going to throw my two cents in on why I chose FPB. I have been wanting a blue car for years since my last one was in 1986 (Lincoln Mark VII LSC) and my favorite blue color Ford had was Liquid Blue. Unfortunately it never made it to production cars or trucks so the next closest color to...

If you are talking about the hood stops on either side (bumpers) there is no actual specs in the repair manual as to measurement height. They just want you to raise or lower to give a proper level or gap between the hood and the fenders. There are two ways that I adjust those stops. One...

Like everyone else, I agree it is most likely the hood bumper stops being misadjusted (too high) causing the hoods to crack. Back about 11 months ago in one of the "1st mods" threads, I posted how the first day I had the car I had to adjust the hood latch and both bumper stops as the hood was...

I didn't even notice the fuel gauge at 3/4. Now I understand what you meant. Anxious to check out the videos.

Tom, were you joking about the 50 miles to empty low fuel warning or being serious? I ask because anytime mine get to 50 miles to empty I get the same warning and thought it was normal.

That is a good rule of thumb and like I said earlier, happens to be the setting (21) where I start to hear distortion from the test tones. Again, I was using an iPhone 12 Pro for the input and I am sure it would vary a bit depending on your source but going past 20 on the volume with my input...

Yes your amp most likely does that. Many amps today will adjust for the incoming input voltage. Meanwhile, I am glad Scott got his sub working correctly. I talked to his installer and explained exactly what to do and sounds like he has all the bass he needs now. 😊

Mine was ceramic coated with Ceramic Pro 9H a week after I got the car. It will be a year old next month and so far 4200 miles. Not many miles but it looks brand new.

Ok, as promised, I went out and measured the input voltage coming into my JM500/1 JL Audio 500 watt mono amp. The signal was originally going into the OEM B&O sub. This JL amp only has a left and right RCA inputs so I terminated the wires from the OEM sub with a left and right RCA plug. This...