Search results

Hey guys, I'm going to be swapping in a PP rad and the support braces, but not sure what else I need to install the braces. Do I need four Hinge Nuts (W716409-S442), is there something else, or is everything already there? Looking at the drawing here...

Apologies since this has likely been done to death. I've read some threads and I think I know the answers to these, but just wanted to double check: Is there a passive rear diff cooling option? I've researched this a decent amount, and I am 90% sure the answer is no. I'd be ok using the GT350...

I'm seeing that for the Corsa Touring AB and Sport CB the 2018+ exhaust is cheaper than the 15-17 and the quad tips look great. Will the 2018+ exhaust fit on the 15-17 with the Roush valance or with the mod to the stock rear valance?

Hey guys, I ordered some parts for my Mustang and they arrived like the the attached pictures. The solution I was offered by the vendor was that they would pay to have the parts painted. They arrived like this from the manufacturer and they were shipped out accordingly. If I knew this would...

I have seen a huge variety of numbers on YouTube and this forum for the axle nut sizes. For rear I have seen 32mm (a couple DIYers), 36mm (CJ Pony Parts) and 1.25" (LMR). Can someone who has taken their rear hub off please confirm the size? Same for the front? I'm also assuming I should have...

To those who have done this, what did you use to cut the rear premium bumper? I'm referring to this step of the installation. I feel like laying it paint side down on some pads with clean microfiber towels on top then cutting from behind with a dremel might be the safest approach?

I'm looking to put some jacking rails on my Mustang ahead of doing work on it. I was planning on getting the Steeda low profile ones. I noticed rust around the bolt holes. Both sides look similar. Aside from this, the underside of my car looks pretty good. Exhaust, exhaust hangers and sway bars...

I've seen some threads here mentioning that 2021 and newer had corrected the cooling of the OEM 4-piston rotors. Is it possible to buy those OEM replacement front rotors for an older Mustang? RockAuto is showing BRRF447 and BRRF439. It looks like BRRF447 is vented inside based on the pics I...

Can the a set of base GT500 wheels with the OEM tires fit on a regular GT? Is a spacer needed in the front? It looks like the fronts are 20x11 +32mm with 305/30R20.

Is the 18+ Premier Trim center console soft touch like the new knee bolsters or is it hard plastic just with some stitching added towards the front? I'm planning on ordering the knee bolsters since I know they're nice, but the center console is expensive. Not sure if it's worth it. I have a...

Hey guys, I'm looking to do a handling upgrade on my 16 GT. It does not have the performance pack and is stock. I've owned it since new and I'd like to make it more aggressive and fun. I'm planning to do all the mods in my garage with a buddy. I want something that can be installed relatively...

Hey everyone, I've had my A/C repaired 3 times. Here is a link to the work they did. The last time I put in a ticket w/Ford Corporate. I'm planning to do that again. My appointment is next Friday. Is the dealer doing anything obviously wrong based on the linked repairs performed? Is there...

Hey guys, I'm attempting to program a third fob. I have the first two. I've tried three times, and each time I receive the following messages: Has anyone else done this successfully? I purchased the fob from this eBay Auction that I found linked in this thread. Edit: I got it...

I placed my order on 2/15, and my build was scheduled on 2/18 but dealer didn't get me the VIN until today. Build date was listed as week of 3/14/2016. This will be my daily driver. I'm not a car track fiend like others here, although I've done track days on my bike. Guard Metallic 401A...