Search results

I know there are a couple of members here, who have attempted to delete magneride on their cars using the SDE deletes and experiencing problems with them not working properly. I just purchases the same kit before I ran across the thread mentioning the problems that end users were having with...

Hello, @KellTrac, I recently ordered a pair of S550 Viking Crusader “Ultra Spec“ Inverted rear shocks for my 2019 Bullitt Mustang. I am looking for assistance with dialing in shock settings for both street and strip. Here are the specifics pertaining to my car: Coyote engine - Ultimate LTHs...

I recently finished up my MT82-D4 tranny build and started the car for thr first time today. I noticed a knocking sound coming from what I am pretty certain is the throwout bearing because it knocks at an idle while in neutral and goes away when the clutch is depressed. I didn’t want to take it...

I am trying to wrap up the remaining miscellaneous work on my 2019 Bullitt, so that I can immediately put the car back on the road when my driveshaft arrives. One of the last few things I have to do is flush out the remaining orange factory coolant and get ready to add new Motorcraft yellow...

Does anyone know where I might find a dummy plug to serve as a weatherproof cover for the IMRC wiring harness 3 pin connector?

Is anyone running the Steeda idler and tensioner pulleys? I just received mine today and I stalled them. The pulley that fits onto the boss in the engine cover fits perfectly (no wobble), whereas the tensioner pulley has a slight wobble (can move it by hand). Followed the instructions in the...

Is anyone running one of the Steeda aluminum driveshafts on their 2018+ 6speed manual transmission? Looking for feedback on how smooth it is and how well it performs. Thanks

Does anyone have first hand knowledge of how to successfully remove solid dowel pins from aluminum casings Without causing any damage to the dowel or casing? I need to remove two of them from my transmission cover. Any help would be greatly appreciated. Thanks

Are there any experienced Tig aluminum welders near the Parrish/Sarasota Florida area on here? I’m looking for someone to weld a couple of 6061 aluminum bungs to my transmission housing, as well as a 3” long bead (both sides) on a Closed Corner Joint for an external fluid pump mount. See pics...

I installed an MMR IMRC Lockout Kit on my Bullitt intake manifold and have an under standing that a retune is necessary. I’ve spoken to Lund Racing about this and they said they would have to write new tunes, but no data logging would be required. I had a thought this morning that perhaps I...

Can anyone advise what would be the best high temperature grease for the MT82-D4 transmission’s input, output and countershaft bearings? I pulled the seals from all three (new) bearings and cleaned all of the factory grease out of them before sending them out for cryogenics treatment. When I get...

Can someone please tell me what the FSM says the flywheel bolt torque and tightening sequence is? Thank you.

Does anyone have a damaged MT82-D4 input shaft (needs to have perfect splines), that they would be willing to sell? I’d like to make a clutch alignment tool out of one that is stronger than the plastic one I have.

I went to install my new Ram Pro Street Clutch today using ARP bolts for the Coyote engine and discovered that there’s only 1/4” of useable thread protruding from the back of the flywheel. The factory flywheel bolts are 1 3/8” long and the ARP bolts are only 1” long. What’s everyone doing here...

Has anyone installed an MMR CMCV/IMRC Lockout Kit on a 2019 GT350 intake manifold? I currently have my IM off of the car and would like to remove all the crap off the back of it to clean it up and make more room for my MMR Head Oiling and Cooling Mods. I currently have an nGauge with great...

I started disassembling the MY82-D4 from my 2019 Bullitt today and confirmed that the shift forks are not the upgraded metal or steel ones that I’ve heard many say Ford had upgraded to (including the repairing of some problematic 2018 GTs). Have a look for yourselves here.

I’m not sure if this is the correct place to post this, but I thought it might be, due to the likelihood that a lot of GT350 owners track their cars and perform their own maintenance. With that being said, her it goes. I have a 2 post lift being delivered in about 10 days. I’ve researched the...

To all of the Ben Calimer Stage 1, 2 or 3 users, can we hear from you guys as to how well/or not you transmission has held up? I’d like to know the following: - How many miles have you put on it? - Has it handled WOT and No Lift Shifting well (for WOT Box users)? - Any crunching and grinding of...

For those of you, who have suffered a failure or damage of any kind with your MT82, will you please post pics of the carnage and give a brief synopsis of what you were doing when the failure occurred?

i just ordered a Ram Pro Street Clutch Kit for my 2019 Bullitt. A representative from Ram told me that the correct clutch alignment tool was not available yet. I inquired about where to get one and he said that would throw the one in that they have, but a longer one was really needed. He...