Search results

  1. SOLD MY CAR :(

    Hey gang, had to sell my beloved Bullitt. It was just sitting in the garage, and with 5 freaking (rare cancer) relapses in 6 years (I need treatment again now), I've spent a small fortune (and counting), so my big house with my 4-car garage is gone, and can only have 1 car now, and the Bullitt...
  2. Bullitt 2019 Green/black, fully loaded (+ cover). Only 4,510 miles. Immaculate. Original owner. El Paso, TX

    Sold to Vroom for $43,884 (I was ASKING $44K). Hope this helps somebody.
  3. B&O center (dash) speaker replacement guide request

    Hey gang, I already used the 'B&O 10" sub replacement guide' to replace the crappy B&O sub with the Pioneer. I was going to leave it at that, but now that a new incessant (and ultra annoying) dash rattle emerged, I'll have to remove the damn dash trim again, which I did for the first time when...
  4. Unbelievable racket from the door when car sits in the cold. What could it be?

    Hey gang, curious if this has happened to anybody else. Fortunately, it only happens twice (in Marfa, TX), when car sat outside, in the cold. And both times just to go to a restaurant, fortunately. The racket was unbelievable. Lowering the window just a little bit stopped it completely, so...
  5. Who here has adjusted the parking brake free play?

    I want to eliminate the free play my parking brake handle has, which is about an inch. It doesn't trigger the dash light, but if you leave it up, it stays there. If you push it down, it stays there, but sometimes it moves up that inch while driving, and I don't like that. In addition, when I...
  6. Help with code BCM 726-41-02 xxxx x*xx change requested.

    I often leave my doors 'open' (meaning closed but just to the first 'click') in the garage, and even after the battery saver feature turns everything off after 15 minutes or so, the battery still gets depleted more than it should, at the tune of about 0.07V every day (and that's on a brand new...
  7. My first DTC (seat module -SCME). Input welcome.

    Hey gang, did a quick FORScan change, and immediately noticed a DTC when it connected, which was the first time ever (pictures below). Probably happened on our last trip, where we used the seat ventilation (very ineffective, by the way) for several hours. I grabbed something from behind my...
  8. Ebay got me with a fake 'OEM' plastic drain plug. Input wanted.

    Hey gang, bought a drain plug I thought was OEM on eBay, but as always, didn't carefully read the entire description, and the aholes listed their non-OEM plug as 'OEM spec', to hopefully confuse buyers like me, and I was one of them. Failed to read the entire post, where the manufacturer was...
  9. Any way to lessen the force needed to open the hood? Thx

    Ever since I opened the hood of my Bullitt at the dealer for the first time, I knew it wasn't normal to require that much force to open. I thought it was just too tight... which it was. But that wasn't the issue. I adjusted the hood properly when I got home, by raising the latch a little (after...
  10. Has anybody here enabled euro emergency brake flashing???

    I'm talking about the feature that when braking hard (don't know how hard), the brake lights reportedly flash quickly 'x' amount of times, to alert motorists following you that you're braking hard. To be precise, I'm talking about the following FORScan change: BCM 726-26-02 xxxx x1. Looked...
  11. Has anybody with a stock PP1 car driven it on Rhino ramps in reverse?

    Need to know if it clears the front lip. I'm by myself, and don't want to destroy it. Ha ha. The good news is the front lip (barely) clears the Rhino ramps (without any 2x6 'assistance') if driving forward, which I'm about to do for the first time to change the oil, and install the front Steeda...
  12. Who has done a DIY oil change on your Bullitt? Need input on how to access oil filter. Thx.

    Hey gang, I'm going to do my first oil change very soon now, with 1,086 miles on the clock at the moment. Just waiting to see if Steeda is going to send the black braces or not, so I don't have to put the car on ramps again a week later. At any rate, read that there was a 'door' to access the...
  13. Engine production question

    Hey gang, just saw today a square label with a QR code at the back of the left (driver's side) valve cover on my engine, when checking oil level. It has a date of May 28, 2019, while my car was built in August 09, 2019. Is that the engine build date, or just the valve cover build date? Never...
  14. Can you access the 2nd climate screen on your Bullitt with Sync3.4?

    Hey gang, turns out there's a second climate screen on Sync 3.4 that shows the heated/cooled soft buttons there (when activated with FORScan via this code: APIM 7D0-01-01 xxxx xxxx x6xx)... but can't figure out how to access it. Can somebody please post how, to see what the heck I'm missing...
  15. Anybody with really nice BLACK carpeted floor mats, front and rear? Please jump in.

    Hey gang, I want to replace the OEM floor mats on my Bullitt with better quality carpeted ones, including a properly placed heel guard on the driver's side, and rear mats too. I bought the OEM rubber set, but looks crappy on the Bullitt, so only used the rear ones in the mean time, rather than...
  16. Best BLACK rear sub-frame brace for a Bullitt

    Hey gang, since I don't want any less ground clearance than stock, nor any added ride stiffness, nor NVH, decided to just add rear sub-frame braces, and a front 2-point G-brace, to improve handling a little. I'm not sure if the front G-brace helps with cornering, so please let me know, since I...
  17. Looking for an oil filter socket for the FL500S. Thx.

    Hey gang, I'm at 950+ miles, and want to do the first oil change around 1K. But just realized the space to remove the filter on my Bullitt (with a front belly pan) is very limited, so probably impossible to use my plier-type oil filter wrench. So need a socket wrench that can hopefully withstand...
  18. Bullitt handling improvements without reducing ground clearance, ride, or NVH.

    Hey gang, like most of you, I'm satisfied with the overall performance of my Bullitt, because in order to have a 'grand tourer' with decent street manners, it's obviously going to have some handling compromises. And I'm fine with them for the most part. BUT, if I can improve the handling a...
  19. Rear caliper retracting tool

    Hey gang, will replace all pads on my 900+ mile 2019 Bullitt, and in case the new pads (I'm debating if Z23s or Z26s) are wider, I'd have to retract the rear pistons, so I'm looking for the proper tool to do that. I want the simplest possible one but with correct fit. Looked at those 3/8"...
Top