Search results

  1. Steeda Adjustable Differential Bushing Insert - Install Tip

    I installed the Steeda Adjustable Diff Bushing Insert kit (555-4443) yesterday, and wanted to pass along a couple of tips that will get your install time down from the 4 hours it took me to the 1 hour it SHOULD have taken me. Of note, I also have the Steeda IRS Subframe Alignment Kit, IRS...
  2. South Carolina Steeda IRS Subframe Alignment Kit and Subframe Bushing Support Kit

    Received these as extra items in a lot I purchased from another member here, and I already have them. Looking to either sell them outright for $160, plus shipping and Paypal fees, or ideally, to trade them for Steeda Rear Adjustable Camber Arms, plus $$$. Brand new in bag, and they're a pretty...
  3. Charleston Alignment Shops

    All - I'm about to install the Steeda Toe Links and need a better alignment than I trust the national chains to do. If it were my wife's Benz, I'd take it to Karl at European Road and Racing, but he's way too busy to touch a domestic car. Who's your go-to shop in the Charleston area? I'm close...
  4. Installing Ford Performance Cam Covers - Replace VCT?

    I'm waiting on Levittown Ford to ship out my Ford Performance cam covers (M-6067-M52S), as I have the small oil leak at the #8 cylinder, due to the design of the stock cam covers. I saw that some folks have issues with their VCT Solenoids after awhile. I'm at 51k miles. Does it make sense to...
  5. GT350 Center Gauges - No MyColor?

    I just installed a set of GT350 gauges in my 2016 Performance Pack GT. They're working fine, and they light up with a while backlight. Do these gauges not work with MyColor? I'm unable to change the backlighting, for whatever reason. It's not that big a deal, I just usually keep all my...
  6. South Carolina FS: GT Performance Package trim panels with Vac/Oil Pressure Gauges

    $350 + shipping. Recently removed from my GT. There's very light surface scratching on the bigger piece that I tried to capture. It is not very noticeable under all situations. There is one broken tab (thanks, Ford) on the lower right corner. The Vacuum and Oil Pressure gauges were included...
  7. Mold Inside Car

    Admittedly, this isn't about my Mustang, but my Camaro. It rarely gets driven, because it's a giant pain in the butt to get started (big block), and to protect it from my kid and his friends, it sits under a car cover. I keep Damp Rid buckets in the car, but if I don't check it often enough, it...
  8. Valve Stems

    A buddy is a tech at the local Benz/Jag/Alfa/Porsche dealer and is mounting my Ford Performance PP2 wheels tomorrow. He asked me to bring valve stems, but I honestly have no idea what I need. Anyone know if these will work?
  9. South Carolina WTB: Gloss Black 2018+ PP1 Spoiler

    Located in Charleston, SC. Looking for a new or well cared for PP1 spoiler in factory black. Willing to trade my GT350 Track Pack spoiler.
  10. P0171 and P2197 Codes after Airbox Swap

    Sunday morning, I pulled the front of my car apart to install my Big Mouth, as well as my 2018 airbox and intake tube. I pulled off the stock 2016 intake tube, then realized that I had not accounted for the fact that the 2016 has two vacuum connections (in addition to the sound tube), while the...
  11. Plug Well Seal Replacement

    My back two plug well seals are leaking on the driver's side cylinder head. Does anyone have a shop manual with procedure for this? My car has already had the TSB applied for leaking valve cover gasket, due to too few bolts being installed from the factory. Thanks, JR
  12. Does new AC Compressor Kit come with Clutch?

    Hey all - After about three years, and 25k miles, my AC compressor and/or clutch has failed. Again. This was all replaced under warranty a few years ago, along with the evaporator. The story goes that I started hearing bearing noises, and knew I would need to replace the clutch, at minimum...
  13. Are 2018 Injectors Worth Anything?

    I bought a 2018 GT manifold, and the seller included the fuel rail and injectors. Are they worth anything? For reference, these are the top injectors, not the DI injectors. JR
  14. Borked my front bumper - have questions

    I was pulling out of my garage earlier, and not paying as much attention as I should have, and this was the result... The bumper may need to be replaced, though the scratches aren't deep, they just went through the color and clear. The fender likely just needs a respray on the wheel arch...
  15. Blipshift GT350R Shirt

    Today has a new R shirt! https://www.blipshift.com/products/r-seltongue?utm_source=blipshift+Updates&utm_campaign=adb83f1c49-RSELTONGUE_2020_03_16&utm_medium=email&utm_term=0_0513fd2cb9-adb83f1c49-345825781&mc_cid=adb83f1c49&mc_eid=1f361133a1 JR
  16. Snap/Click from driver's rear suspension

    For a few months now, I've had a weird snap/click sound from the driver's rear suspension that's heard on slow speed take offs, both when turning and when straight. I initially thought it was the halfshaft, but it's not cyclical like a halfshaft failure would be. It clicks a couple times...
  17. How to replace PCV valve?

    Backstory - When I installed my McLeod clutch line two weeks ago, I had trouble seating the fitting into the hard line at the master cylinder. To get a better angle, I climbed on top of the intake manifold. Issue - Today while I was sitting at a red light, I saw some gray smoke coming from the...
  18. Axle bearing install

    Has anyone installed axle bearings in the S550 rear? I'm going to be swapping axles, and might as well do the seals and bearings while I have the axles removed. Seals seem like they'd be simple enough to remove and replace. JR
  19. Clutch Line Upgrades

    Has anyone used the McLeod braided clutch line, as opposed to the SR (which has bad reviews) or the Steeda? I like that the McLeod has screw-in fittings, as opposed to the line being integrated into the fitting, like the Steeda. Unfortunately, American Muscle's website shows the McLeod clutch...
  20. Overpressurizing Master Cylinder

    Hey everyone. I was just using my brand new Motive Power Bleeder to flush my brake system. I was keeping the system pressurized to 15 PSI +/- 2 PSI. While I was doing the front passenger Brembo, the Bleeder fell off the shelf I had it sitting on, and the nipple that goes into the cap was...
Top