Search results

  1. Maine Wanted Whipple 3.675 pulley.

    I need a whipple pulley 3.675”
  2. Maine MFP 6 rib crank support

    SOLD Installed and run for 60 miles. Belt contacted lower support stand due to install error. Cosmetic damage to stand only.
  3. My Whipple Cobra Jet install.

    I did a lot of searching for CJ inlet installs and really there isn't much out there, hard to even find pics of what the filter fender well area looks like installed with from clip off. So I though I'd post up some pics and of course I'd have to change things and maximize as much as possible...
  4. My Whipple Cobra Jet inlet installation.

    I did a lot of searching for CJ inlet installs and really there isn't much out there, hard to even find pics of what the filter fender well area looks like installed with from clip off. So I though I'd post up some pics and of course I'd have to change things and maximize as much as possible...
  5. Making power with Meth injection share your success.

    I've seen threads pop up here from time to time asking about making power with Meth, and I'm always surprised at how phew are using meth with these cars which so easily can make 800 wheel with some octane resistance fuels. With states like Cali's 91 and many with no E85, just seems this combo...
  6. My whipple FORE L2 fuel system experience.

    FORE Innovations fuel system setups are some really sweet and quality kits no doubt, and I was impressed with the overall quality of the kit for sure. Installing their kit on a Whipple using Whipple rails leaves some question unanswered in their install instructions. Many have done this, and I'm...
  7. GT ATI balancer and APR bolt and washer

    SOLD ATI balancer and APR bolt and washer used for 10k miles. $225 shipped
  8. Maine 72 Lb Whipple/DW injectors for sale

    These injectors have been used for approximately 13k miles on a Whipple setup. Selling as I've upgraded to FORE fuel system with ID1050X injectors. $275 shipped
  9. Maine MSD fuel pump booster #2351 and harness for S550 plug and play

    SOLD Used for 2 years flawlessly, but upgraded to FORE dual pump for 850-1000 wheel coming. This plug and play setup literally plugs in between stock fuel pump harness and pump under the back seat and then power and ground. $275 shipped Sells new for $415 without the S550 fuel pump plug and...
  10. High HP 3" exhaust resonator fitment issue.

    So I've been looking for a solution for my 3" exhaust with Kooks 1 7/8 long tubes no cats, I don't want it loud. Currently have the Borla 60561 resonator but it has 2.5" outlet and necked down even more to 2.25" inlet and it does a bang up job of lowering the sound levels. I thought maybe the...
  11. 15 Gen 4 Whipple PBD Cal...What will it make?

    Back story this car made 730 Wheel corrected 2 years ago with 3.5 pulley Gen 3 whipple 93 fuel and small shot of meth injection at 18 degrees timing 0 knock 7800 rpm with stock headers and CATS on a Whipple cal. Now with same 3.5" pulley, but Gen 4 Whipple with Kooks 1/7/8" long tubes catless...
  12. Engine on power source for IC pump.

    I went from the Whipple cal which uses the IMRC connector in the back which is programmed in the Whipple cal to turn on pump when engine is running. Now with PBD cal that same connection turns pump on and off with key on. Is there a power source under the hood that can be tapped into to turn...
  13. Ngauge...where's Injector Duty cycle PID

    I just got HP Tuners PBD Ngauge and can't find the PID for injector duty cycle. I selected Ford gas 2008 and newer and it came up with 90 PID'd I think, but nothing shows up for IDC. What am I missing?
  14. Maine Lund NGauge-For sale

    SOLD SOLD SOLD In perfect condition like new, I only used it for logging. Will need to be unlocked by Lund for your calibration, but all other features and full logging ability is available. Comes with OBD2 data cable not pictured. $225 shipped.
  15. Dampers for Eibach Sportline springs

    I'm looking to replace my stock springs on my Whipple GTPP. Street car only, and mainly looking for damper that will control these Sportline progressive springs. Likely with my weight up front from the Whipple and electronics in the trunk I'd see close to what they rate the convertibles at 1.6"...
  16. UPR Whipple catch can

    in perfect condition and works with 15-17 Whipple setups. SOLD SOLD SOLD mustang-billet-plug-n-play-catch-can-separator-15-whipple-css.html
  17. Gen 4 whipple sneak peak

    So it’s not new news that Whipple has been working on releasing a new 2.9L Gen 4 for the 17 and earlier Mustangs, but I got one now. I was able to secure and early pre production Gen 4 as a beta tester, and opted for gloss white powder coating option. I’ve had all 3 now since buying my first Gen...
  18. My Huge 20 x 12" wheels widened thread.

    So I've put this info and pics in other threads here, but I though I would dedicate for searching reasons one consolidated thread on my 20x10" rears wheels being widened 2" to. Firstly Weldcraft was great in getting my wheels done, and really happy if went with them. Despite my lack of reading...
  19. 3/8" 9.5mm Hubcentric wheel spacer

    SOLD SOLD SOLD Mounted once, but never used $25 shipped.
  20. Steeds rear lower control arm bushings NEW!

    SOLD SOLD Never Installed NIB Steeda rear Lower control arm bushings 555-4117. SOLD SOLD...
Top