Post Pix of your S550 with aftermarket wheels and tires

[GEBRONI]

@GEBRONI looks good!

What rear diffuser and quad tip set up are you running? Looks like GT350? Ford part or aftermarket?

Thanks!

Thanks @DRKHORS!!! It is OEM GT350 rear valance... I do not advise do any other but OEM for true plug and play no modification except cutting the premium bumper where needed. Quad tips from eBay where seller used some of my pics: https://www.ebay.com/itm/262535959579. I would like them 2-3 inches shorter but not much to play from end of muffler to valance, really tight and a lot of after market tips are long... I have Borla cat back exhaust as well, think the Roush canisters are shorter so easier to fabricate y pipe for GT350 fixed tips or after market tips... I also installed used like new the GT350 side skirts... You need to purchase all new clips for that swap!

Sponsored

 

[shogun32]

Konig Centigram 19x9.5 et35 CG9N514357
Fits over Brembo 6-pot.

 

[shogun32]

IMG_20191121_134656897

• shogun32
• Nov 21, 2019

2019-11-21 11.10.51

• shogun32
• Nov 26, 2019

DR48 9.5ET40 wheel 'poke'

DR48 19x9.5 et40

 

[Dave2013M3]

I haven't seen alot of pictures of the SVE X500 in silver out in the wild, so here's one. I am very happy with how they look. 19x10 with the stock summer Pirellis 275 square setup.

I'm not a huge fan of black wheels. The silver really pops against the dark blue. These wheels have this AC Schnitzer look that I liked on BMWs from the late '80s.

Looks great, waiting for my set to arrive. I did the staggered 19X10 and 19X11 with 275/35/19 and 295/35/19.

 

[myblkshadow19]

You guys running the 20" rims with 35 profile tire, did you have to adjust the speedo for the diameter increase?

according to lund racing the 15+ cars for the gears/tires are not controlled by the pcm but the bcm. not 100% what the bcm is but this is what i have in an email...hope it helps

 

[GEBRONI]

I have power pack 2 with ProCal tune... In that software I can reflash with the correct revs per mile

 

[KermiStang]

Too much?

 

[RubyRed15]

Needs more camber.

 

[GEBRONI]

Needs more camber.

and Liberty wide body kit ;-)

 

[EPTS550]

Voxx GT500 Replica Squared Setup. 19x10 et40mm. 285-35R19

 

[GUSTOPP2]

Still rolling on these beaters.

Staggered TE37 OG’s
F: 19x9.5 +35 (with 5mm spacer)
R: 19x10.5 +35

So bad ass. Always have loved these wheels. I wish they offered Mustang specific sizing.

 

[Shane361]

 

[GEBRONI]

FYI for anyone who wants to see the fitment of 19x10 rim with 40mm offset wrapped in 285/35r19 Michelin (which runs wide) clearance to the front struts. No rubbing. That dirt off the strut is brushed off from the little ¿nipples? found on new tires. It is a tight fitment ;-)

 

[shogun32]

It is a tight fitment ;-)

really? Looks like an easy 10mm to me.

 

[GEBRONI]

really? Looks like an easy 10mm to me.

can't get in there to take a better line of sight pitcure when the suspension is loaded. Probably the angle adds some mm's to your estimate, I am sure it is about 5mm or so between the tire and strut. The rim clearance is just fine.

Sponsored