Sponsored

Base Audio upgrade to JL 3 way and more !

5.0_SD

Village Idiot/Biermeister
Joined
Feb 24, 2017
Threads
25
Messages
1,136
Reaction score
395
Location
Central Florida
First Name
Bill
Vehicle(s)
17 GT Base Lightning Blue
Ya it's funny, my funnel was sitting in the well, took me a couple minutes to figure out it clipped to that black plastic on the left center, lol.
Sponsored

 
OP
OP

Dutch44

Active Member
Joined
Sep 20, 2018
Threads
5
Messages
43
Reaction score
7
Location
Russia
Vehicle(s)
2017 Mustang GT , 2008 Jeep Sahara , 2004 ford explorer
Ya it's funny, my funnel was sitting in the well, took me a couple minutes to figure out it clipped to that black plastic on the left center, lol.
I'm wondering what the clip on the right is too hold ?
 

5.0_SD

Village Idiot/Biermeister
Joined
Feb 24, 2017
Threads
25
Messages
1,136
Reaction score
395
Location
Central Florida
First Name
Bill
Vehicle(s)
17 GT Base Lightning Blue
Ah, the mystery deepens!
 
OP
OP

Dutch44

Active Member
Joined
Sep 20, 2018
Threads
5
Messages
43
Reaction score
7
Location
Russia
Vehicle(s)
2017 Mustang GT , 2008 Jeep Sahara , 2004 ford explorer
Ah, the mystery deepens!
Good luck with your build . It seems this forum is against Americans freedom of speech ! Peace
 

5.0_SD

Village Idiot/Biermeister
Joined
Feb 24, 2017
Threads
25
Messages
1,136
Reaction score
395
Location
Central Florida
First Name
Bill
Vehicle(s)
17 GT Base Lightning Blue
Good luck with your build . It seems this forum is against Americans freedom of speech ! Peace
Not sure what you mean by the freedom of speech thing...what I meant in my comment was that I have no idea what the right side of the plastic opposite where the funnel clips in is for. Thank for the well wishes for my build :)
 

Sponsored

mustank

Well-Known Member
Joined
May 23, 2016
Threads
12
Messages
184
Reaction score
39
Location
APO
Vehicle(s)
2016 mustang gt
I finally got it all installed a few weeks ago , I have been working on getting the blower and the air lift suspension gathered up before I tear it down again . I put the JL rear speakers as components and flush mounted the tweeter on the side panel and cut out the rear deck board for the speaker covers to fit on top , used a stinger at the battery terminal , the Amp is located under the rear deck " I borrowed that idea " and the crossovers I mounted below the Amp , I put dyna mat behind the tweeter and the wheel wells , The Amp power cable I ran through the firewall like most did but I slid it up next the the other wire harness it comes out above the A/C lines , and routed it inside through the passenger side black plastic tray box along the bottom door jam it's a tight fit , took it all apart then ran the wire and snapped it back together and redid the wire ties . Ran RCA's from the head unit on the driver side under the carpet and seat .. I took out the ford sync as it was in the way .. it sounds really good right now kinda took away my beautiful exhaust notes I had going on now with the long tubes and such ..
IMG_20181019_230325.jpg
IMG_20181014_011621.jpg
IMG_20181021_013701.jpg
IMG_20181019_230414.jpg
IMG_20180915_120810.jpg
IMG_20180915_113853.jpg

I approve of that amp mount :thumbsup:
 

5ABI VT

Well-Known Member
Joined
Oct 6, 2015
Threads
34
Messages
799
Reaction score
263
Location
Gta
Vehicle(s)
2015 mustang GT
Setup looks great ! Looks like the jl 3 way component setup for the front and a 2 way for the rear with the tweet mounted into the rear quarter panels? I have a base and Id like to add the 3 way setup in mine up front and 2 way in the rear.
 

Canoman

Lurker (mostly)
Joined
Jul 31, 2017
Threads
7
Messages
102
Reaction score
20
Location
Wylie, TX
First Name
John
Vehicle(s)
2017 GT PP 400A
Vehicle Showcase
1
One of the pics shows a second level of amp-mount that hangs the crossovers under the amp, but the pic with the amp mounted in the car doesn't show the crossovers level. Just curious - where did the crossovers end up?
 

stone36441

Member
Joined
Dec 16, 2019
Threads
1
Messages
15
Reaction score
0
Location
United States
Vehicle(s)
2017 mustang gt
The addition of two molex connectors , the pod made from 3/8 ABS , mountings are from ACE and are the Chrysler license plate fastner. The molex connectors are attached to 18 AWG separated from speed wire from mousers which I ran through the harness after I removed the bottom door speaker wire to relocate inside the door . The molex connectors are slightly bigger so some patience and persuading efforts where needed . The speaker grill I have to figure out next ,. I asked someone from Craigslist doing doing 3D printing but they wanted about 250 dollars .
IMG_20180831_222708.jpg
fullsizeoutput_211.jpeg
IMG_20180930_012119.jpg
IMG_20180930_005838.jpg
IMG_20180930_004218.jpg
IMG_20180930_005612.jpg
IMG_20180929_235648.jpg
IMG_20180922_011414.jpg
IMG_20180922_012249.jpg
IMG_20180922_001208.jpg
IMG_20180930_004149.jpg
Did you have to use a certain crimping tool to connect the speaker wire to the pin. Are the pins posi much a direct fit? When you purchased these was there a minimum to buy?
Sponsored

 
 




Top