cyberdude47
Member
I have a OBDlink MX, blutooth. can this switch be installed onto this?
Sponsored
you don't need it, the MX will read all BUS's without the switch being necessary.I have a OBDlink MX, blutooth. can this switch be installed onto this?
What’s your VIN? I’ll do some research later.Okay, got everything programmed the way I want and working. Only trouble spot is the LC toggle on my bezel won't respond. Anyone know the values for that? I haven't seen that line specifically listed.
I have seen it suggested that you just reflash everything to a similar model to your upgrade but I went the other route and only modified things that I knew would need to change.
I'm going to test these two a bit later:What’s your VIN? I’ll do some research later.
The line of code referenced in the spreadsheet is this:Yes - take a look at the spreadsheet on the FORSCAN Codes thread below (let me know if this helps)
https://www.mustang6g.com/forums/showthread.php?t=98260
Thanks, I may try this in my Sync 3 swapped base car.The line of code referenced in the spreadsheet is this:
7D0-01-01 : xxxx xxxx x?xx
- changing the value with the question mark will only disable the soft climate buttons for the heated seats and steering wheel.
What I am curious about is this coding:
7D0-01-01 : xxxx xxx? xxxx
According to the F150 spreadsheet, changing the value at this locaiton tells the APIM what type of climate system you have and you have HD radio as well (Climate Front Zone & HD Radio: 3=Dual Zone & HD radio avail, 2=Dual Zone & HD radio not avail, 7=Single Zone & HD radio avail, 6=Single Zone & HD radio not avail).
On my as built data sheet, I have the following code: 7D0-01-01: 0C67 9800 04E8
So to truly disable the dual climate zone soft button and settings and not have a code thrown as has been talk about earlier, I would have to change the 0 to a 6. The question is, would this affect the FCIM controls and how they function (meaning only one climate control wheel would work or both could still adjust the temp in the car).
Thanks
Have you had a chance to try this yet? I have come up with what I am hoping to do:Thanks, I may try this in my Sync 3 swapped base car.
To be honest, I would leave most of that stuff alone (factory settings) aside from the dual climate setting, which I want to try when I get time.Have you had a chance to try this yet? I have come up with what I am hoping to do:
AS BUILT: 7D0-01-01: 0C67 9800 04E8
TO BE CHANGED TO - 7D0-01-01: 622A 0506 00xx
Ignore the xx's at the end since that will be the checksum value calculated by forescan.
This coding should do the following:
1. enable the reverse camera
2. limit the stereo to play for only 20 minutes after turning off the ignition
3. Not exactly sure what the "A" in the first block does, but the F150 sheet mentions something about the steering wheel control switches
4. Have rotary volume display
5. Tell the car that no auxiliary inputs are present and to enable the radio fader settings and that the car uses a push to start button
6. Tell the car that it will be does not have a dual climate system and no HD radio
7. There are no heated or cooled seats in the car.
DO you see any problems with this coding. I probably spent around 3 hours today working over this (not just this one line, but all the lines I am hoping to modify).
Cheers
To get the doors to lock as you reach 20kph this is the code and it works on my16I’m not sure but I think you’re screenshot shows the the option for automatic locking doors when you start moving. The setting for the keyboard being accessible while moving is in the APIM:
7D0-02-01 **** xxxx xxxx
It’s actually the Country Code: 5553=U.S., 4341=CANADA;
If you use 5753 (which translates to WS whatever that means) it will allow NAV in motion on Sync2, but Sirius Travel Link no longer works.
have you had a go at trying these? i think i tried a couple and it didn't work but it did change the camera view, i'm planning on having a forscan day this coming weekend got a few mods i want to activate i'll try going through this list to see what happensIv'e looked through the thread again. Anyone tried the fuel prime on door code from the F150 sheets?
726-41-01 xxxx x*xx xxxx Fuel Prime on Door Ajar Cfg: 0=no prime, 1=prime
Also interested in a soft touch button for the rear camera:
D0-02-02 xxxx x*xx xxxx Camera Toggle Button (CTB) & Trailer Reverse Guidance (TRG) & CHMSL Camera & Aux Camera
54
0=CTB hard & TRG disabled & CHMSL disabled & Aux Camera disabled
8=CTB soft & TRG disabled & CHMSL disabled & Aux Camera disabled
55
1=CTB hard & TRG disabled & CHMSL disabled & Aux Camera enabled 9=CTB soft & TRG disabled & CHMSL disabled & Aux Camera enabled
56
2=CTB hard & TRG disabled & CHMSL enabled & Aux Camera disabled A=CTB soft & TRG disabled & CHMSL enabled & Aux Camera disabled
57
3=CTB hard & TRG disabled & CHMSL enabled & Aux Camera enabled B=CTB soft & TRG disabled & CHMSL enabled & Aux Camera enabled
58
4=CTB hard & TRG enabled & CHMSL disabled & Aux Camera disabled C=CTB soft & TRG enabled & CHMSL disabled & Aux Camera disabled
59
5=CTB hard & TRG enabled & CHMSL disabled & Aux Camera enabled D=CTB soft & TRG enabled & CHMSL disabled & Aux Camera enabled
60
6=CTB hard & TRG enabled & CHMSL enabled & Aux Camera disabled E=CTB soft & TRG enabled & CHMSL disabled & Aux Camera disabled
61
7=CTB hard & TRG enabled & CHMSL enabled & Aux Camera enabled F=CTB soft & TRG enabled & CHMSL enabled & Aux Camera enabled
That's a great question. If you find the answer, please let me know and I'll update the spreadsheet with the correct/updated info.The line of code referenced in the spreadsheet is this:
7D0-01-01 : xxxx xxxx x?xx
- changing the value with the question mark will only disable the soft climate buttons for the heated seats and steering wheel.
What I am curious about is this coding:
7D0-01-01 : xxxx xxx? xxxx
According to the F150 spreadsheet, changing the value at this locaiton tells the APIM what type of climate system you have and you have HD radio as well (Climate Front Zone & HD Radio: 3=Dual Zone & HD radio avail, 2=Dual Zone & HD radio not avail, 7=Single Zone & HD radio avail, 6=Single Zone & HD radio not avail).
On my as built data sheet, I have the following code: 7D0-01-01: 0C67 9800 04E8
So to truly disable the dual climate zone soft button and settings and not have a code thrown as has been talk about earlier, I would have to change the 0 to a 6. The question is, would this affect the FCIM controls and how they function (meaning only one climate control wheel would work or both could still adjust the temp in the car).
Thanks